Global robotics standards update

Keeping standards up to date with technology: Industrial robot safety standards remain in development to help lower risk for those integrating, implementing, using and maintaining robotics.

04/10/2018


Sometimes it seems safety around industrial equipment, including robotics, can be very complicated. Technical experts in the robotics industry have developed national and international industry standards that can help remove a lot of the mystery around robots and safety. As technology continues to improve, so must the standards documents.

As of March 2018, a number of new or updated standards documents are in development by technical experts globally. A few robot safety standards efforts for robot manufacturers, integrators, and end users are explained below. 

International standards

The Robotic Industries Association (RIA) works within the ISO framework to support the development of international standards on robotics. The ISO group responsible for global robotics standards is ISO Technical Committee (TC) 299, Robotics, and it has published an international standard (IS) on safety requirements for industrial robots and robot systems, as well as supplemental documents that provide guidance on topics such as collaborative robot safety and safety design for manual load/unload stations. 

Safety Standard: ISO 10218-1,2:2011. This document, published in 2 parts, describes safety requirements that the robot manufacturers and systems integrators must meet. Requirements for the robot, which robot manufacturers must meet, are the topic of Part 1 of 10218. Part 2 addresses requirements to systems integrators for developing an overall robot system that will help keep a safe environment for human workers in the area.

Image courtesy: Bob Vavra, CFE MediaThis document is crucial for robot manufacturers and integrators to obtain, understand, and use. Suppliers to the robotics industry, and end-users of robot systems, are encouraged to understand these documents, as well, to help them be at their most effective in doing business with robot manufacturers and integrators.

Currently, the 10218 standard is undergoing a periodic updating and the update is planned for publication in 2021. 

New ISO Technical Reports: ISO/TR 20218-2, Safety Design for Manual Load/Unload Stations.  This document is designed for use with the 10218 standard.

ISO/TR 20218-2:2017 aims to resolve the difficulties that might arise when safety requirements for industrial robots clash with safety requirements for ergonomics. For example, one safety requirement for traditional (safeguarded) industrial robot systems is to surround the robot cell with perimeter fencing to a height of 1400 mm.

But what happens when an employee must interact with the robot system, whether loading or unloading? An expectation of lifting the input or output to a height of 1400 mm is unreasonable from an ergonomic standpoint. How can those involved resolve and minimize these separate but related two sources of risk (robot system vs. ergonomic risk)? This ISO TR was developed to help answer that question.

This document is most useful for integrators and users of robot systems.

The ISO/TR 20218-2 technical report was published in December 2017.

ISO/DTR 20218-1, Safety Design for End-Effectors. This document is designed for use with the 10218 standard.

The ISO/DTR 20218-1 is still in the publication process-that's what the "D" means in its designation code: Draft. The goal of this document is to describe safety best practices regarding end-effectors (end-of-arm-tooling, or EOAT). The industrial robot itself cannot do any work; it must be integrated into an overall robot system, including end-effectors, which manipulate the workpiece and perform the work. Some end-effectors are suitable for collaborative work (near humans), and some are not-the risks they present are too high. This document examines a wide range of end-effector types, lists examples of potential hazards from end-effectors, and gives guidance to reduce risks associated with end-effectors.

Carole Franklin is director of standards development at the Robotic Industries Association (RIA). Courtesy: RIAThis document is useful to integrators of robot systems as well as suppliers of end-effectors and tool changers. Industrial robot end users may also find it valuable information to help keep their workers safe around end-effectors. The ISO/DTR 20218-1 is expected to be published later in 2018.

Carole Franklin is director of standards development at the Robotic Industries Association (RIA). The RIA is a part of the Association for Advancing Automation (A3), a CFE Media content partner. Edited by Mark T. Hoske, content manager, Control Engineering, CFE Media, mhoske@cfemedia.com.

KEYWORDS

Global safety standards, robots

Safety Standard: ISO 10218-1,2:2011 is being updated.

ISO/TR 20218-2, Safety Design for Manual Load/Unload Stations was published in December 2017.

ISO/DTR 20218-1, Safety Design for End-Effectors is expected later in 2018.

Consider this

U.S. robotic safety standards are harmonized with global robotic standards.

ONLINE

Control Engineering has a robotics page



Top Plant
The Top Plant program honors outstanding manufacturing facilities in North America.
Product of the Year
The Product of the Year program recognizes products newly released in the manufacturing industries.
System Integrator of the Year
Each year, a panel of Control Engineering and Plant Engineering editors and industry expert judges select the System Integrator of the Year Award winners in three categories.
September 2018
2018 Engineering Leaders under 40, Women in Engineering, Six ways to reduce waste in manufacturing, and Four robot implementation challenges.
July/Aug
GAMS preview, 2018 Mid-Year Report, EAM and Safety
June 2018
2018 Lubrication Guide, Motor and maintenance management, Control system migration
August 2018
SCADA standardization, capital expenditures, data-driven drilling and execution
June 2018
Machine learning, produced water benefits, programming cavity pumps
April 2018
ROVs, rigs, and the real time; wellsite valve manifolds; AI on a chip; analytics use for pipelines
Spring 2018
Burners for heat-treating furnaces, CHP, dryers, gas humidification, and more
August 2018
Choosing an automation controller, Lean manufacturing
September 2018
Effective process analytics; Four reasons why LTE networks are not IIoT ready

Annual Salary Survey

After two years of economic concerns, manufacturing leaders once again have homed in on the single biggest issue facing their operations:

It's the workers—or more specifically, the lack of workers.

The 2017 Plant Engineering Salary Survey looks at not just what plant managers make, but what they think. As they look across their plants today, plant managers say they don’t have the operational depth to take on the new technologies and new challenges of global manufacturing.

Read more: 2017 Salary Survey

The Maintenance and Reliability Coach's blog
Maintenance and reliability tips and best practices from the maintenance and reliability coaches at Allied Reliability Group.
One Voice for Manufacturing
The One Voice for Manufacturing blog reports on federal public policy issues impacting the manufacturing sector. One Voice is a joint effort by the National Tooling and Machining...
The Maintenance and Reliability Professionals Blog
The Society for Maintenance and Reliability Professionals an organization devoted...
Machine Safety
Join this ongoing discussion of machine guarding topics, including solutions assessments, regulatory compliance, gap analysis...
Research Analyst Blog
IMS Research, recently acquired by IHS Inc., is a leading independent supplier of market research and consultancy to the global electronics industry.
Marshall on Maintenance
Maintenance is not optional in manufacturing. It’s a profit center, driving productivity and uptime while reducing overall repair costs.
Lachance on CMMS
The Lachance on CMMS blog is about current maintenance topics. Blogger Paul Lachance is president and chief technology officer for Smartware Group.
Material Handling
This digital report explains how everything from conveyors and robots to automatic picking systems and digital orders have evolved to keep pace with the speed of change in the supply chain.
Electrical Safety Update
This digital report explains how plant engineers need to take greater care when it comes to electrical safety incidents on the plant floor.
IIoT: Machines, Equipment, & Asset Management
Articles in this digital report highlight technologies that enable Industrial Internet of Things, IIoT-related products and strategies.
Randy Steele
Maintenance Manager; California Oils Corp.
Matthew J. Woo, PE, RCDD, LEED AP BD+C
Associate, Electrical Engineering; Wood Harbinger
Randy Oliver
Control Systems Engineer; Robert Bosch Corp.
Data Centers: Impacts of Climate and Cooling Technology
This course focuses on climate analysis, appropriateness of cooling system selection, and combining cooling systems.
Safety First: Arc Flash 101
This course will help identify and reveal electrical hazards and identify the solutions to implementing and maintaining a safe work environment.
Critical Power: Hospital Electrical Systems
This course explains how maintaining power and communication systems through emergency power-generation systems is critical.
Design of Safe and Reliable Hydraulic Systems for Subsea Applications
This eGuide explains how the operation of hydraulic systems for subsea applications requires the user to consider additional aspects because of the unique conditions that apply to the setting
click me