Basics of belt drives

Power transmission belting has been used for more than 200 years. The first belts were flat and ran on flat pulleys. Later, cotton or hemp rope was used with V-groove pulleys to reduce belt tension. This led to the development of the vulcanized rubber V-belt in 1917. The need to eliminate speed variations led to the development of synchronous or toothed belts about 1950 and the later deve...

09/01/2001


Key concepts

For long life, select the belt type best suited for the application.

There are three basic types of power transmission belting: flat, V, and synchronous.

Misalignment is a common cause of premature belt failure.

Sections:
Belt types
Alignment
Tension

Sidebars:
Belt drive advantages
Belt drive disadvantages


Power transmission belting has been used for more than 200 years. The first belts were flat and ran on flat pulleys. Later, cotton or hemp rope was used with V-groove pulleys to reduce belt tension. This led to the development of the vulcanized rubber V-belt in 1917. The need to eliminate speed variations led to the development of synchronous or toothed belts about 1950 and the later development of fabric-reinforced elastomer materials.

Today, flat, V, and synchronous belting is still being used in power transmission. When compared to other forms of power transmission, belts provide a good combination of flexibility, low cost, simple installation and maintenance, and minimal space requirements.

Belt-driven equipment uses readily available components. Replacement parts can be easily obtained from local distributors. This availability reduces downtime and inventory. Sheaves and pulleys are usually less expensive than chain drive sprockets and have little wear over long periods of operation.

Belt types

All power transmission belts are either friction drive or positive drive. Friction drive belts rely on the friction between the belt and pulley to transmit power. They require tension to maintain the right amount of friction. Flat belts are the purest form of friction drive while V-belts have a friction multiplying effect because of wedging action on the pulley.

Positive drive or synchronous belts rely on the engagement of teeth on the belt with grooves on the pulley. There is no slip with this belt except for ratcheting or tooth jumping.

Flat belts

Modern flat belts are made with reinforced, rubberized fabric that provides strength and high friction levels with the pulley (Fig. 1). This eliminates the need for high tension, lowering shaft and bearing loads. Flat belts can transmit up to 150 hp/in. at speeds exceeding 20,000 fpm.


Fig. 1. Flat belts have thin cross-sections and wrap around pulleys easily

A significant advantage of flat belts is efficiency of nearly 99%, about 2.5-3% better than V-belts. Good efficiency is due to lower bending losses from a thin cross-section, low creep because of friction covers and high modulus of elasticity traction layers, and no wedging action into pulleys.

Pulley alignment is important to flat belts. Belt tracking is improved by crowning at least one pulley, usually the larger one. Flat belts are forgiving of misalignment; however, proper alignment improves belt life.

Different flat belt surface patterns serve various transmission requirements. In high-horsepower applications and outdoor installations, longitudinal grooves in the belt surface reduce the air cushion flat belts generate. The air cushion reduces friction between the pulley and belt. The grooves nearly eliminate the effects of dirt, dust, oil, and grease and help reduce the noise level.

Flat belts operate most efficiently on drives with speeds above 3000 fpm. Continuous, smooth-running applications are preferred. Speed ratios usually should not exceed 6:1. At higher ratios, longer center distances or idlers placed on the slack side of the belt create more wrap around the smaller pulley to transmit the required load.

V-belts


Fig. 2. V-belts come in

V-belts are commonly used in industrial applications because of their relative low cost, ease of installation, and wide range of sizes (Fig. 2). The V-shape makes it easier to keep fast-moving belts in sheave grooves than it is to keep a flat belt on a pulley. The biggest operational advantage of a V-belt is the wedging action into the sheave groove. This geometry multiplies the low tensioning force to increase friction force on the pulley sidewalls (Fig. 3).


Fig. 3.

Classical V-belts are frequently used individually, particularly in A and B sizes. The larger C, D, and E sizes generally are not used in single-belt drives because of cost penalties and inefficiencies. Multiple A or B belts are economical alternatives to using single-belt C, D, or E sections.

Narrow V-belts, for a given width, offer higher power ratings than conventional V-belts. They have a greater depth-to-width ratio, placing more of the sheave under the reinforcing cord. These belts are suited for severe duty applications, including shock and high starting loads.

Banded V-belts solve problems conventional multiple V-belt drives have with pulsating loads. The intermittent forces can induce a whipping action in multiple-belt systems, sometimes causing belts to turn over. The joined configuration avoids the need to order multiple belts as matched sets.

Banded V-belts should not be mounted on deep-groove sheaves, which are used to avoid turnover in standard V-belts. Such sheaves have the potential for cutting the band of joined belts. Extremely worn sheaves produce the same result.

V-ribbed belts combine some of the best features of flat belts and V-belts. The thin belt operates efficiently and can run at high speeds. Tensioning requirements are about 20% higher than V-belts. The ribs ensure the belt tracks properly, making alignment less critical than it is for flat belts.

Synchronous belts

Synchronous belts have a toothed profile that mates with corresponding grooves in the pulleys, providing the same positive engagement as gears or chains. They are used in applications where indexing, positioning, or a constant speed ratio is required.

The first tooth profile used on synchronous belts was the trapezoidal shape (Fig. 4). It is still recognized as standard. Recent modifications to tooth profiles have improved on the original shape. The full-rounded profile distributes tooth loads better to the belt tension members. It also provides greater tooth shear strength for improved load capacity.


Fig. 4. Synchronous belts have several tooth shapes

A modified curvilinear tooth design has a different pressure angle, tooth depth, and materials for improved load/li fe capacity and nonratcheting resistance.

Synchronous belts can wear rapidly if pulleys are not aligned properly, especially in long-center-distance drives, where belts tend to rub against pulley flanges. To prevent the belt from riding off the pulleys, one of them is usually flanged. A recent development has produced a belt and pulley that use a V-shaped, instead of straight, tooth shape. It runs quieter than the other shapes and doesn't require pulley flanges.

Undertensioning causes performance problems. The drive may be noisy because belt teeth do not mate properly with pulley grooves or the belt may prematurely wear from ratcheting. High forces generated during belt ratcheting are transmitted directly to shafts and bearings and can cause damage.

Link belts

Link-type V-belts consist of removable links that are joined to adjacent links by shaped ends twisted through the next link (Fig. 5). With this design, belts can be made up of any length, reducing inventory. The belts are available in 3L, A/4L, B, C, and D widths in lengths from 5 to 100 ft.


Fig. 5. Link-type belts are used to make instant V-belt replacements

These belts can transmit the same horsepower as classic V-belts. The links are made of plies of polyester fabric and polyurethane that resist heat, oil, water, and many chemicals.

Advantages of link belts include quickly making up matched sets, fast installation because machinery doesn't have to be disassembled, and vibration dampening.

Disadvantages include cost and the possible generation of static charges. The belt should be grounded when used in high-dust applications.

Alignment

Misalignment is one of the most common causes of premature belt failure (Fig. 6). The problem gradually reduces belt performance by increasing wear and fatigue. Depending on severity, misalignment can destroy a belt in a matter of hours. Sheave misalignment on V-belt drives should not exceed 1/2 deg. or 1/10 -in. of center distance. For synchronous belts it should not exceed 1/4 deg. or 1/16-in. of center distance.


Fig. 6. Improper drive maintenance is the biggest source of belt drive problems

Angular misalignment (Fig. 7) results in accelerated belt/sheave wear and potential stability problems with individual V-belts. A related problem, uneven belt and cord loading, results in unequal load sharing with multiple belt drives and leads to premature failure.

Angular misalignment has a severe effect on synchronous belt drives. Symptoms such as high belt tracking forces, uneven tooth/land wear, edge wear, high noise levels, and potential failure due to uneven cord loading are possible. Wide belts are more sensitive to angular misalignment than narrow belts.


Fig. 7. Misalignment causes belt wear, noise and excessive temperatures

Parallel misalignment also results in accelerated belt/sheave wear and potential stability problems with individual belts. Uneven belt and cord loading is not as significant a concern as with angular misalignment.

Parallel misalignment is typically more of a concern with V-belts. They run in fixed grooves and cannot free float between flanges to a limited degree as synchronous belts can. Parallel misalignment is generally not a critical concern with synchronous belts as long as the belt is not trapped or pinched between opposite sprocket flanges and tracks completely on both sprockets.

Tension

Total tension required in a belt drive depends on the type of belt, the design horsepower, and the drive rpm. Since running tensions cannot be measured, it is necessary to tension a drive statically.

The force/deflection method is most often used. Once a calculated force is applied to the center of a belt span to obtain a known deflection, the recommended static tension is established. Most design catalogs provide force and deflection formulas.

With too little tension in a V-belt drive, slippage can occur and lead to spin burns, cover wear, overheating of the belt, and possibly overheating of bearings. Not enough tension in a synchronous belt causes premature tooth wear or possible ratcheting that will destroy the belt and could break a shaft.

When installing a new belt, installation tension should be set higher. Generally 1.4-1.5 times the normal static tension. This is necessary because drive tension drops rapidly during the seating-in process. This extra initial tension does not affect bearings because it decays rapidly.

Plant Engineering magazine extends its appreciation to The Goodyear Tire & Rubber Co. for its cooperation in making the cover photo possible.

Belt application matrix

Application

Synchronous belt

V-belt

V-ribbed belt

Polyurethane

Rubber

Double-sided

Heavy- duty

Light-duty

Polyurethane

Speed/Load

High speed

2

2

1

1

Low speed

1

1

2

3

High load

1

2

4

3

3

Low load

1

2

3

4

4

Shock/impulse load

3

4

1

2

Serpentine drive

1

Serpentine drive w/ shock load

2

Twisted drive

1

2

3

Clutching drive

1

2

Index drive w/high load

1

Index drive w/low load

1

2

Drive characteristics

Reversing direction

1

1

3

4

2

Frequent start/stop

1

1

3

4

2

Start under load

1

2

3

Smooth running

3

2

1

1

Variable speed

1

Oil, chemical environment

1

3

4

2

High temperature

1

2

4

4

3

Low temperature

1

2

3

4

1=First choice, 4=Last choice Chart courtesy The Gates Rubber Co.


Troubleshooting V-belt drives

Problem

Cause

Remedy

Belt stretch beyond take-up

Belts stretch unequally

Misaligned drive overloading some belts. Belt tensile member broken from improper installation

Realign and retension drive. Replace with a new, matched set, properly installed

All belts stretched equally

Insufficient take-up allowance

Check take-up and follow recommended allowance

Greatly overloaded or under-tensioned drive

Redesign drive

Short belt life

Rapid belt failure

Tensile members damaged from improper installation

Replace with new, matched set, properly installed

Worn sheave grooves

Replace sheaves

Under-designed drive

Redesign drive

Belt sidewalls soft and sticky. Low adhesion between cover, plies. Cross section swollen

Oil or grease contamination of belt/sheave

Remove source of oil or grease. Clean belts and sheave grooves cloth moistened with nonflammable, non-toxic degreasing agent or commercial detergent and water

Belt sidewalls dry and hard.

High-temperature environment

Remove source of heat

Low adhesion between cover and plies

Ventilate drive

Deterioration of belt's rubber compounds

Belt dressing

Never use dressing on rubber V-belts. Clean belts and sheave grooves cloth moistened with nonflammable, non- toxic degreasing agent or commercial detergent and water. Tension drive properly to prevent slip

Extreme cover wear

Belts rubbing against belt guard or other obstruction

Remove obstruction or align belts to provide proper clearance

Spin burns on belt

Belts slip on starting or load stalls

Retension drive

Bottom of belt cracked

Sheaves too small

Redesign drive for larger sheaves

Broken belts

Object falling into or hitting drive

Replace with new, matched set of belts

Belt turnover

Excess lateral belt whip

Use banded belt

Foreign material in sheave grooves

Remove material. Shield drive

Misaligned drive

Realign drive

Worn sheave grooves

Replace sheaves

Tensile member broken from improper installation

Replace belts with new, matched set, properly installed

Incorrectly placed idler pulley

Carefully align idler pulley on slack side of drive, as close as possible to driver sheave

Belt noise

Belt slip

Retension drive

Improper driven speed

Incorrect driver/driven ratio

Design error

Change sheaves

Hot bearings

Drive overtensioned

Worn sheave grooves. Belts bottom out and can't transmit power unless overtensioned

Replace sheaves. Tension drive properly

Improper tension

Retension drive

Sheaves too small

Motor/belt manufacturer's recommendations not followed

Redesign drive

Bearing wear

Underdesigned bearings or poor bearing maintenance

Observe recommended design and maintenance

Drive undertensioned

Belts slip and cause heat buildup

Retension drive


Power transmission belting manufacturers
The following companies provided input for this article by responding to a written request from Plant Engineering magazine. For more information on their product lines, circle the number on the Reader Service Card or visit their web site.

Circle

Company

Belt type

Horsepower range

Speed range, fpm

Max. length, in.

221

Fenner Drives

V

1/16—6

275—600

none

fennerindustrial.com

Flat

0.01—0.1

98—196

none

Link

varies by application

222

Emerson Power

V

1.3—925

1000—6500

450

emerson-ept.com

Synchronous

3.8—318

1000—6500

270

Link

1.3—16

1000—5000

450

223

The Gates Rubber Co.

V

0.1—1000

1—20,000

663

gates.com

Synchronous

0.1—1200

1—15,000

270

Flat

0.1—50

1—25,000

126

Link

0.1—50

1—7000

none

224

Goodyear Tire & Rubber Co.

V

0—1000

0—10,000

900

goodyearptp.com

Synchronous

0—1100

0—20,000

280

Flat

0—500

0—10,000

1620

226

Shingle Belting Co.

V

4—16

1000—5000

open

Flat

1—20

1000—8000

open

225

Stock Drive Products/Sterling Instr.

V

0.1—4.5

500—12,000 rpm

32.5

sdp-si.com

Synchronous

0.01—18

8000—25,000 rpm

149.6

Flat

0.04—0.2

2000—20,000 rpm

19.7



Belt drive advantages

Cleanliness

Lubrication-free

Absorbs shock loads

Wide selection of speed ratios

Can provide variable speeds

Quiet operation

Efficiency over 95%

Transmits power between widely spaced shafts

Visual warning of failure

Belt drive disadvantages

Need to retension periodically

Deterioration from exposure to lubricants or chemicals

Cannot be repaired, must be replaced



No comments
The Top Plant program honors outstanding manufacturing facilities in North America. View the 2015 Top Plant.
The Product of the Year program recognizes products newly released in the manufacturing industries.
The Engineering Leaders Under 40 program identifies and gives recognition to young engineers who...
2016 Product of the Year; Diagnose bearing failures; Asset performance management; Testing dust collector performance measures
Safety for 18 years, warehouse maintenance tips, Ethernet and the IIoT, GAMS 2016 recap
2016 Engineering Leaders Under 40; Future vision: Where is manufacturing headed?; Electrical distribution, redefined
SCADA at the junction, Managing risk through maintenance, Moving at the speed of data
Safety at every angle, Big Data's impact on operations, bridging the skills gap
The digital oilfield: Utilizing Big Data can yield big savings; Virtualization a real solution; Tracking SIS performance
Applying network redundancy; Overcoming loop tuning challenges; PID control and networks
Driving motor efficiency; Preventing arc flash in mission critical facilities; Integrating alternative power and existing electrical systems
Package boilers; Natural gas infrared heating; Thermal treasure; Standby generation; Natural gas supports green efforts

Annual Salary Survey

Before the calendar turned, 2016 already had the makings of a pivotal year for manufacturing, and for the world.

There were the big events for the year, including the United States as Partner Country at Hannover Messe in April and the 2016 International Manufacturing Technology Show in Chicago in September. There's also the matter of the U.S. presidential elections in November, which promise to shape policy in manufacturing for years to come.

But the year started with global economic turmoil, as a slowdown in Chinese manufacturing triggered a worldwide stock hiccup that sent values plummeting. The continued plunge in world oil prices has resulted in a slowdown in exploration and, by extension, the manufacture of exploration equipment.

Read more: 2015 Salary Survey

Maintenance and reliability tips and best practices from the maintenance and reliability coaches at Allied Reliability Group.
The One Voice for Manufacturing blog reports on federal public policy issues impacting the manufacturing sector. One Voice is a joint effort by the National Tooling and Machining...
The Society for Maintenance and Reliability Professionals an organization devoted...
Join this ongoing discussion of machine guarding topics, including solutions assessments, regulatory compliance, gap analysis...
IMS Research, recently acquired by IHS Inc., is a leading independent supplier of market research and consultancy to the global electronics industry.
Maintenance is not optional in manufacturing. It’s a profit center, driving productivity and uptime while reducing overall repair costs.
The Lachance on CMMS blog is about current maintenance topics. Blogger Paul Lachance is president and chief technology officer for Smartware Group.
This article collection contains several articles on the vital role of plant safety and offers advice on best practices.
This article collection contains several articles on the Industrial Internet of Things (IIoT) and how it is transforming manufacturing.
This article collection contains several articles on strategic maintenance and understanding all the parts of your plant.
click me