What’s holding back wireless communication in industry?

In spite of healthy growth, the vast majority of devices will still be connected to wires by 2015, suggesting that the wireless industry isn't as vast as commonly thought.

06/24/2011


In a recent study, IMS Research estimated that the overall industrial wireless market would grow at an average annual growth rate of 18% to the end of 2015 (see Figure 1). That’s certainly well above the average rate we’d consider “normal” for industrial automation products (more typically 5-8%). This certainly explains the vendor community’s attraction to wireless products – how many areas of automation are both fast growing and high margin?

Figure 1: Chart outlining worldwide unit shipments of industrial wireless products. Courtesy: IMS Research

However, when you consider the relatively small size of the industrial wireless market, the attraction starts to wane! Despite the strong growth forecast for wireless networked devices, the vast majority of devices will continue to be connected with fibre and copper. Even by 2015, only 1.5% of devices shipped are forecast to be connected with a wireless network (about 3M wireless devices of an estimated 200M networkable devices shipped).

So what exactly is holding wireless in industry back? Well, first of all, the above statistics don’t tell the whole story. The growth forecast for the relative market sizes of wireless products sold to discrete and process industries varies significantly (see Figure 2).

Figure 2: Chart outlining worldwide unit shipments of all networked products. Courtesy: IMS Research

One of the most influential factors is the nature of production in each industry. So far, automation component vendors have largely released products that focus on wire replacement. Due to the vast nature of process plants these wireless products are very attractive compared to the wired alternative. As copper prices continue to increase, pushing up the cost of networking components using wire, the benefits of wireless networking will also increase. Larger process plants are likely to be the biggest winners. Wireless measurement devices can help to provide more process data and in most cases can easily be integrated with existing wired networks. Two typical application examples can be found here and here.

Process industries have the higher rate of wireless penetration. For example, in 2009 – a tough year for process equipment in general – unit shipments of wireless process measurement instruments doubled. The future for these products also looks bright. Customers have trialled these products with initial success, with a future aim of rolling them out more widely. Wireless devices are appearing in plans for large Greenfield sites in the Middle East, India and China. In 2015, IMS Research projects that over 300K new wireless process measurement devices will be shipped. Whilst this figure represents a small proportion of total process equipment shipped, penetration is undoubtedly increasing.

Wire replacement applications have the potential to seed the market for future growth. Over the next few years, wireless will begin to extend its application reach with new solutions that will begin to focus on model-based maintenance, asset management and energy management.

However, the story for discrete automation is quite different. A wide variety of products targeted at this space do currently exist, but penetration within the market is much lower. While the benefits of networking in machines are well known, the smaller distances associated with machinery connectivity (either within the machine itself, or between different connected machines) mean that replacement of wired components with wireless alternatives has less of a cost benefit. Smaller cost benefits achievable from wireless monitoring devices and the use of wireless components for critical (machine control) applications are still some way off. Consequently, there is still some work to do before wireless technology is widely accepted by machine builder and discrete end-users.

To get traction, automation component vendors need to find new wireless use cases in discrete factory automation. It is likely that the current development of discrete automation wireless technologies will help – but market penetration won’t approach the level of process automation by 2015. Without a doubt, a huge potential for wireless technologies in discrete automation applications exists, and penetration will undoubtedly increase. However, due to the smaller potential cost reductions, it’s imperative that dedicated discrete wireless technologies and compelling use cases are established to increase market penetration.



Top Plant
The Top Plant program honors outstanding manufacturing facilities in North America.
Product of the Year
The Product of the Year program recognizes products newly released in the manufacturing industries.
System Integrator of the Year
Each year, a panel of Control Engineering and Plant Engineering editors and industry expert judges select the System Integrator of the Year Award winners in three categories.
September 2018
2018 Engineering Leaders under 40, Women in Engineering, Six ways to reduce waste in manufacturing, and Four robot implementation challenges.
July/Aug
GAMS preview, 2018 Mid-Year Report, EAM and Safety
June 2018
2018 Lubrication Guide, Motor and maintenance management, Control system migration
August 2018
SCADA standardization, capital expenditures, data-driven drilling and execution
June 2018
Machine learning, produced water benefits, programming cavity pumps
April 2018
ROVs, rigs, and the real time; wellsite valve manifolds; AI on a chip; analytics use for pipelines
Spring 2018
Burners for heat-treating furnaces, CHP, dryers, gas humidification, and more
August 2018
Choosing an automation controller, Lean manufacturing
September 2018
Effective process analytics; Four reasons why LTE networks are not IIoT ready

Annual Salary Survey

After two years of economic concerns, manufacturing leaders once again have homed in on the single biggest issue facing their operations:

It's the workers—or more specifically, the lack of workers.

The 2017 Plant Engineering Salary Survey looks at not just what plant managers make, but what they think. As they look across their plants today, plant managers say they don’t have the operational depth to take on the new technologies and new challenges of global manufacturing.

Read more: 2017 Salary Survey

The Maintenance and Reliability Coach's blog
Maintenance and reliability tips and best practices from the maintenance and reliability coaches at Allied Reliability Group.
One Voice for Manufacturing
The One Voice for Manufacturing blog reports on federal public policy issues impacting the manufacturing sector. One Voice is a joint effort by the National Tooling and Machining...
The Maintenance and Reliability Professionals Blog
The Society for Maintenance and Reliability Professionals an organization devoted...
Machine Safety
Join this ongoing discussion of machine guarding topics, including solutions assessments, regulatory compliance, gap analysis...
Research Analyst Blog
IMS Research, recently acquired by IHS Inc., is a leading independent supplier of market research and consultancy to the global electronics industry.
Marshall on Maintenance
Maintenance is not optional in manufacturing. It’s a profit center, driving productivity and uptime while reducing overall repair costs.
Lachance on CMMS
The Lachance on CMMS blog is about current maintenance topics. Blogger Paul Lachance is president and chief technology officer for Smartware Group.
Material Handling
This digital report explains how everything from conveyors and robots to automatic picking systems and digital orders have evolved to keep pace with the speed of change in the supply chain.
Electrical Safety Update
This digital report explains how plant engineers need to take greater care when it comes to electrical safety incidents on the plant floor.
IIoT: Machines, Equipment, & Asset Management
Articles in this digital report highlight technologies that enable Industrial Internet of Things, IIoT-related products and strategies.
Randy Steele
Maintenance Manager; California Oils Corp.
Matthew J. Woo, PE, RCDD, LEED AP BD+C
Associate, Electrical Engineering; Wood Harbinger
Randy Oliver
Control Systems Engineer; Robert Bosch Corp.
Data Centers: Impacts of Climate and Cooling Technology
This course focuses on climate analysis, appropriateness of cooling system selection, and combining cooling systems.
Safety First: Arc Flash 101
This course will help identify and reveal electrical hazards and identify the solutions to implementing and maintaining a safe work environment.
Critical Power: Hospital Electrical Systems
This course explains how maintaining power and communication systems through emergency power-generation systems is critical.
Design of Safe and Reliable Hydraulic Systems for Subsea Applications
This eGuide explains how the operation of hydraulic systems for subsea applications requires the user to consider additional aspects because of the unique conditions that apply to the setting
click me