Weak output may presage slower growth

The economy showed signs of downshifting as manufacturing cooled last month and consumer spending slowed in September, bolstering expectations of weak growth into early next year.


The economy showed signs of downshifting as manufacturing cooled last month and consumer spending slowed in September, bolstering expectations of weak growth into early next year.
Meanwhile, inflation remained flat in September, according to an inflation gauge that is closely watched by the Federal Reserve.

The latest survey by the Institute for Supply Management confirmed suggestions by the Fed this week that the economy would likely slow in the fourth quarter. Wednesday, the central bank lowered interest rates by a quarter percentage point.

Manufacturers "seem to have run out of our momentum at this point, as far as 2007 is concerned," said Norbert Ore, chairman of the ISM's manufacturing-survey committee.

The ISM's index of manufacturing activity slipped to 50.9 last month from 52 in September. The measure, based on a survey of purchasing managers, put manufacturing growth at its slowest pace since March, reflecting high inventories and rising prices for some materials and supplies. Readings above 50 indicate an expansion in manufacturing activity. Production, a subset of the overall index, plunged after eight months of growth. Strike-related disruptions among auto makers might have been partly to blame, analysts suggested.

Meanwhile, economic growth from abroad continues to prop up U.S. manufacturers. The ISM survey found export demand surging because of the weak dollar, while manufacturers' imports fell for the first time in nearly six years. The ISM found that manufacturing employment edged higher in October, a positive signal. "You're going to see very, very modest increases in manufacturing activity for a while," said Morgan Stanley economist David Greenlaw.

Firms may be feeling early signs of inflationary pressures. Manufacturers indicated they paid more for materials such as oil and steel in October. That could presage higher prices for consumer goods. Inflation had remained tame through much of this year, giving Fed officials latitude to lower interest rates at their last two meetings.

In a separate report, the Department of Commerce said the price index for personal-consumption expenditures rose 0.2% in September after being unchanged in August. Compared with a year earlier, the index gained 2.4%; the August increase was 1.8%.

The Fed's preferred inflation gauge -- the "core prices" which exclude volatile food and energy prices -- rose 0.2% in September after climbing 0.1% in August. Measured from a year earlier, core prices rose 1.8% in September, the same as in August. That puts inflation within the 1%-to-2% comfort zone of some Fed officials. The government said income rose 0.4% in September, the same as in August. Consumers showed signs of turning cautious, a potentially worrisome signal for the holiday shopping season. Consumer spending rose 0.3% in September -- the slowest since June -- after rising 0.5% in August.

Consumer spending may face more pressure if surging oil markets push prices higher at gasoline pumps. The threat to consumer outlays comes as a deepening housing downturn pressures household finances. Home foreclosures in the third quarter rose more than 30% from the second quarter to 446,700 properties nationwide, double the level of a year earlier, RealtyTrac Inc. said yesterday.

Separately, jobless claims edged lower last week, but a tick up in the trend suggests growth may remain sluggish. Initial claims for unemployment compensation fell 6,000 to a seasonally adjusted 327,000 last week, the Labor Department said. The four-week moving average for claims, an indication of the underlying strength of the job market, rose 1,750 to a six-month high of 327,000.

Top Plant
The Top Plant program honors outstanding manufacturing facilities in North America.
Product of the Year
The Product of the Year program recognizes products newly released in the manufacturing industries.
System Integrator of the Year
Each year, a panel of Control Engineering and Plant Engineering editors and industry expert judges select the System Integrator of the Year Award winners in three categories.
October 2018
Tools vs. sensors, functional safety, compressor rental, an operational network of maintenance and safety
September 2018
2018 Engineering Leaders under 40, Women in Engineering, Six ways to reduce waste in manufacturing, and Four robot implementation challenges.
GAMS preview, 2018 Mid-Year Report, EAM and Safety
October 2018
2018 Product of the Year; Subsurface data methodologies; Digital twins; Well lifecycle data
August 2018
SCADA standardization, capital expenditures, data-driven drilling and execution
June 2018
Machine learning, produced water benefits, programming cavity pumps
Spring 2018
Burners for heat-treating furnaces, CHP, dryers, gas humidification, and more
October 2018
Complex upgrades for system integrators; Process control safety and compliance
September 2018
Effective process analytics; Four reasons why LTE networks are not IIoT ready

Annual Salary Survey

After two years of economic concerns, manufacturing leaders once again have homed in on the single biggest issue facing their operations:

It's the workers—or more specifically, the lack of workers.

The 2017 Plant Engineering Salary Survey looks at not just what plant managers make, but what they think. As they look across their plants today, plant managers say they don’t have the operational depth to take on the new technologies and new challenges of global manufacturing.

Read more: 2017 Salary Survey

The Maintenance and Reliability Coach's blog
Maintenance and reliability tips and best practices from the maintenance and reliability coaches at Allied Reliability Group.
One Voice for Manufacturing
The One Voice for Manufacturing blog reports on federal public policy issues impacting the manufacturing sector. One Voice is a joint effort by the National Tooling and Machining...
The Maintenance and Reliability Professionals Blog
The Society for Maintenance and Reliability Professionals an organization devoted...
Machine Safety
Join this ongoing discussion of machine guarding topics, including solutions assessments, regulatory compliance, gap analysis...
Research Analyst Blog
IMS Research, recently acquired by IHS Inc., is a leading independent supplier of market research and consultancy to the global electronics industry.
Marshall on Maintenance
Maintenance is not optional in manufacturing. It’s a profit center, driving productivity and uptime while reducing overall repair costs.
Lachance on CMMS
The Lachance on CMMS blog is about current maintenance topics. Blogger Paul Lachance is president and chief technology officer for Smartware Group.
Material Handling
This digital report explains how everything from conveyors and robots to automatic picking systems and digital orders have evolved to keep pace with the speed of change in the supply chain.
Electrical Safety Update
This digital report explains how plant engineers need to take greater care when it comes to electrical safety incidents on the plant floor.
IIoT: Machines, Equipment, & Asset Management
Articles in this digital report highlight technologies that enable Industrial Internet of Things, IIoT-related products and strategies.
Randy Steele
Maintenance Manager; California Oils Corp.
Matthew J. Woo, PE, RCDD, LEED AP BD+C
Associate, Electrical Engineering; Wood Harbinger
Randy Oliver
Control Systems Engineer; Robert Bosch Corp.
Data Centers: Impacts of Climate and Cooling Technology
This course focuses on climate analysis, appropriateness of cooling system selection, and combining cooling systems.
Safety First: Arc Flash 101
This course will help identify and reveal electrical hazards and identify the solutions to implementing and maintaining a safe work environment.
Critical Power: Hospital Electrical Systems
This course explains how maintaining power and communication systems through emergency power-generation systems is critical.
Design of Safe and Reliable Hydraulic Systems for Subsea Applications
This eGuide explains how the operation of hydraulic systems for subsea applications requires the user to consider additional aspects because of the unique conditions that apply to the setting
click me