Use an FEB to ensure safe installation, operation of electrical equipment

Complying with FEB and NRTL standards are vital to ensuring worker safety and standards for electrical products and systems


When AHJs rely on listed or labeled products, it can make the job easier since the inspector does not need to evaluate all the parts as required by NEC 110.3(A). Courtesy: eti Conformity ServicesEvery day, one person dies in the workplace from electrocution, and the United States averages more than 3,600 disabling electrical contact injuries annually, according to the American Society of Safety Engineers. The risk associated with not evaluating or not ensuring the compliance of electrical equipment is very high. That is why the role of third-party testing organizations is so important.

There are two types of organizations that perform product safety testing—a Field Evaluation Body (FEB) and perhaps the more well-known Nationally Recognized Testing Laboratory (NRTL). While similar in their purpose, there are significant differences. Without qualified organizations like FEBs and NRTLs, there would be no way of ensuring that a particular product or installation meets the necessary safety requirements.

NRTLs and FEBs are part of the U.S. electrical safety system that helps ensure safe installations of electrical products and systems. These organizations are usually accepted by local authorities having jurisdiction (AHJs), manufacturers, and others for showing that equipment is suitable for use in the workplace, in construction, or in the home.

Once equipment is deemed to be in compliance with applicable standards, a label is applied. By looking at the NRTL mark or FEB label, an inspector will have information about the standards to which the product has been listed or labeled. In addition, the inspector can call on the NRTL or FEB with questions regarding equipment suitability when something does not look correct.

The National Electrical Code drives local electrical inspectors (AHJs) to look for labels and listing marks. NEC 110.3 provides a list of considerations inspectors need to make when evaluating equipment:

  • Suitability
  • Mechanical strength
  • Wire bending space
  • Insulation
  • Heating effects under normal and abnormal conditions
  • Arcing effects
  • Classification
  • Practical safeguards. 

While 110.3 alone does not require listing or labeling of equipment, it does require considerable evaluation. Section 110.2 requires that equipment be acceptable only if approved, where approved means “acceptable to the AHJ.” The most common form of evidence considered acceptable by AHJs is a listing or labeling by a third party. Another important point is that the NEC requires that the installation instructions included in the listing or labeling be considered during an evaluation.

When AHJs rely on listed or labeled products, it can make the job easier since the inspector does not need to evaluate all the parts as required by NEC 110.3(A). Use of listed or labeled products provides a minimum level of consistent safety when installed properly. This is NRTLs, FEBs, and inspectors working together!

How an NRTL compares to an FEB

National Fire Protection Association (NFPA) 790 is the U.S. standard applicable to FEBs. The most credible method for certification of FEBs involves accreditation to NFPA 790 by a qualified third-party certifier like International Accreditation Services (IAS). FEBs can perform field evaluation services and equipment labeling. NRTLs must comply with the Code of Federal Regulations (CFR) 1910.7 and are certified by OSHA to perform product listing services. OSHA does not certify FEBs, nor does it certify NRTLs to provide FEB services.  

Another important difference between these two organizations is that NRTLs provide product safety testing and certification at the point of manufacture. Their listing process involves rigorous testing of representative samples of a product and the periodic factory follow-up verification and inspection (usually two to four times per year) to ensure new production exactly mirrors the tested samples.

On the other hand, FEBs have the capability to provide product safety testing and labeling primarily in the field for a wide range of products found in the American workplace, while still adhering to stringent national standards from the NFPA:

  • NFPA 790 - Standard for Competency of Third-Party Evaluations Bodies (FEBs)
  • NFPA 791 - Recommended Practice and Procedures for Unlabeled Equipment Evaluation.  

The listings performed by NRTLs and evaluations performed by FEBs are based on product safety standards developed by U.S.-based, standards-developing organizations and often issued under the accreditation of the American National Standards Institute (ANSI). In fact, both testing organizations can determine if an equipment installation is acceptable as defined by CFR 1910.399.

An NRTL would perform the service stipulated in CFR 1910.399 (1), which states that an installation of equipment is acceptable to the Assistant Secretary of Labor if it is accepted, or certified, or listed, or labeled, or otherwise determined to be safe by a nationally recognized testing laboratory pursuant to §1910.7.

Similarly, an FEB can determine acceptability by providing the test data called for CFR 1910.399 (3) which reads as follows: With respect to custom-made equipment or related installations that are designed, fabricated for, and intended for use by a particular customer, if it is determined to be safe for its intended use by its manufacturer on the basis of test data which the employer keeps and makes available for inspection to the Assistant Secretary and his authorized representatives. 

Helping inspectors work more efficiently

Occasionally, a listed or labeled product doesn’t look quite right or has obvious violations. This is when electrical inspectors will notify the NRTL or FEB. The testing organization can determine if it is a counterfeit label, if the equipment was modified, or if a manufacturer is incorrectly manufacturing the product. In any case, the NRTL or FEB has a process to review, evaluate, and stop problems in the future.

In those cases, where an item with violations is holding up the opening of a business, working with an FEB that has the ability to nondestructively test in the field can provide significant time savings, especially with equipment that has been modified, refurbished, or relocated. Such changes normally void the NRTL’s approval of that product, and an employer’s use of it in the workplace violates the OSHA standard requiring the approval.

The FEB provides field label services paid for by one of the parties involved—typically the manufacturer or the installer—to determine if the equipment is compliant in the specific installation. Choosing the right FEB during this critical time is essential.

You’ll want an organization that has a geographically dispersed network of highly trained, safety-certified technicians, along with engineers who know the applicable safety standards for your class of equipment and the reasons behind the standards. Working with engineers who are regular participants in the codes and standards-making processes offers added benefits.

It’s important that an FEB is approved by AHJs from around the country and is recognized in the industry. This makes the process of getting final approval of equipment much smoother. Local jurisdictions know that if the recognized FEB’s label is applied, the job was done right. Working with an experienced FEB inspires confidence and assures others that the equipment was properly inspected and that any discrepancies have been corrected.

A good place to start in the search for an FEB is IAS, which is a nonprofit corporation that has been providing accreditation services since 1975. IAS makes sure that an FEB’s experience, practices, equipment, and processes meet the stringent NFPA 790 and 791 standards, as well as other IAS requirements. The accreditation provides objective evidence that an FEB operates at the highest level of ethical, legal, and technical standards.

The importance of ensuring proper installation and operation of electrical equipment cannot be overstated. After all, many organizations already embrace safety compliance and invest considerable resources in order to protect employees, the environment, and the company as a whole.

Keep in mind that not all testing companies have the competency or experience needed to help you properly protect this investment, so scrutiny is needed when choosing the third-party testing organization that is right for you. An accredited FEB that offers the flexibility of field testing may just be the solution you need to ensure safe operation, get an inspector’s “red tag” removed from your equipment, and get back to business. 

Evaluating a project’s conformity 

Factors that should be considered when evaluating an FEB for a potential conformity project:

1. Objective and Unbiased

  • Independent, professional, third-party testing organization focused on conformity assessment services 

2. Quality

  • Certified by a recognized accreditation body
  • Qualified and trained staff
  • Appropriate quality system in place
  • Financial stability
  • Qualified technical supervision and management 

3. Methodology

  • Documented reference to applicable ANSI or other product safety standards
  • Proper sample control/integrity requirements
  • Testing/evaluation procedures comply with NFPA 790 and 791

4. Responsiveness

  • Complete record keeping system with test data availability
  • Professional systems in place to deliver prompt service 

Wally Vahlstrom brings more than 40 years of electrical engineering experience to his position as the director of technical services for Emerson Network Power’s Electrical Reliability Services group.

Top Plant
The Top Plant program honors outstanding manufacturing facilities in North America.
Product of the Year
The Product of the Year program recognizes products newly released in the manufacturing industries.
System Integrator of the Year
Each year, a panel of Control Engineering and Plant Engineering editors and industry expert judges select the System Integrator of the Year Award winners in three categories.
October 2018
Tools vs. sensors, functional safety, compressor rental, an operational network of maintenance and safety
September 2018
2018 Engineering Leaders under 40, Women in Engineering, Six ways to reduce waste in manufacturing, and Four robot implementation challenges.
GAMS preview, 2018 Mid-Year Report, EAM and Safety
October 2018
2018 Product of the Year; Subsurface data methodologies; Digital twins; Well lifecycle data
August 2018
SCADA standardization, capital expenditures, data-driven drilling and execution
June 2018
Machine learning, produced water benefits, programming cavity pumps
Spring 2018
Burners for heat-treating furnaces, CHP, dryers, gas humidification, and more
October 2018
Complex upgrades for system integrators; Process control safety and compliance
September 2018
Effective process analytics; Four reasons why LTE networks are not IIoT ready

Annual Salary Survey

After two years of economic concerns, manufacturing leaders once again have homed in on the single biggest issue facing their operations:

It's the workers—or more specifically, the lack of workers.

The 2017 Plant Engineering Salary Survey looks at not just what plant managers make, but what they think. As they look across their plants today, plant managers say they don’t have the operational depth to take on the new technologies and new challenges of global manufacturing.

Read more: 2017 Salary Survey

The Maintenance and Reliability Coach's blog
Maintenance and reliability tips and best practices from the maintenance and reliability coaches at Allied Reliability Group.
One Voice for Manufacturing
The One Voice for Manufacturing blog reports on federal public policy issues impacting the manufacturing sector. One Voice is a joint effort by the National Tooling and Machining...
The Maintenance and Reliability Professionals Blog
The Society for Maintenance and Reliability Professionals an organization devoted...
Machine Safety
Join this ongoing discussion of machine guarding topics, including solutions assessments, regulatory compliance, gap analysis...
Research Analyst Blog
IMS Research, recently acquired by IHS Inc., is a leading independent supplier of market research and consultancy to the global electronics industry.
Marshall on Maintenance
Maintenance is not optional in manufacturing. It’s a profit center, driving productivity and uptime while reducing overall repair costs.
Lachance on CMMS
The Lachance on CMMS blog is about current maintenance topics. Blogger Paul Lachance is president and chief technology officer for Smartware Group.
Material Handling
This digital report explains how everything from conveyors and robots to automatic picking systems and digital orders have evolved to keep pace with the speed of change in the supply chain.
Electrical Safety Update
This digital report explains how plant engineers need to take greater care when it comes to electrical safety incidents on the plant floor.
IIoT: Machines, Equipment, & Asset Management
Articles in this digital report highlight technologies that enable Industrial Internet of Things, IIoT-related products and strategies.
Randy Steele
Maintenance Manager; California Oils Corp.
Matthew J. Woo, PE, RCDD, LEED AP BD+C
Associate, Electrical Engineering; Wood Harbinger
Randy Oliver
Control Systems Engineer; Robert Bosch Corp.
Data Centers: Impacts of Climate and Cooling Technology
This course focuses on climate analysis, appropriateness of cooling system selection, and combining cooling systems.
Safety First: Arc Flash 101
This course will help identify and reveal electrical hazards and identify the solutions to implementing and maintaining a safe work environment.
Critical Power: Hospital Electrical Systems
This course explains how maintaining power and communication systems through emergency power-generation systems is critical.
Design of Safe and Reliable Hydraulic Systems for Subsea Applications
This eGuide explains how the operation of hydraulic systems for subsea applications requires the user to consider additional aspects because of the unique conditions that apply to the setting
click me