Tough road ahead for WTO talks, and the manufacturing agenda

We at the National Association of Manufacturers came away from the most recent round of trade talks pleased with the effort by U.S. Trade Representative Rob Portman and U.S. negotiators to hold the line in Hong Kong, but deeply regretful that the World Trade Organization Ministerial meeting did not make the tough decisions needed to negotiate cuts in manufactured goods trade barriers.


We at the National Association of Manufacturers came away from the most recent round of trade talks pleased with the effort by U.S. Trade Representative Rob Portman and U.S. negotiators to hold the line in Hong Kong, but deeply regretful that the World Trade Organization Ministerial meeting did not make the tough decisions needed to negotiate cuts in manufactured goods trade barriers.

Despite the determined efforts by U.S. negotiators, the WTO ministers didn't agree on meaningful guidelines for negotiating manufactured goods trade. Basically, the ministers just kicked the can down the road and pushed the tough decisions out to April 2006.

As an observer at the talks, I did walk away with some good news in that the Hong Kong text calls for sectoral negotiations in addition to a tariff formula. That's important, because the sectoral negotiations are vital. There are 20 or so U.S. industries pressing for such sectoral agreements -- including in electronics, chemicals, wood products and others.

But the other decisions we wanted were not made -- like a meaningful formula that would cut into real tariff rates, or emphasis on non-tariff barriers. The NAM was hoping that ministers would make such fundamental decisions on how tariffs would be cut, how non-trade barriers could be negotiated, and the like. Those decisions did not come. Instead, the WTO ministers are leaving us with four more months of wandering around the desert without a compass.

The problem with this is that a lot of countries don't agree with the basic premise that they have to cut their tariffs on our exports of manufactured goods. They still see the Doha Round (of WTO talks) as essentially a one-way deal in which the U.S. opens up its agricultural market, ends agricultural subsidies and cuts the few remaining high industrial tariffs (textiles, clothing, footwear and light trucks) while they basically do nothing.

Still, the U.S. negotiators didn't lose anything and no doors were shut on us. Hong Kong also may have cleared out some of the underbrush that has diverted attention from the big trade-affecting issues, setting the stage for progress in 2006.

The meeting also heightened pressure on the European Union to move further in opening up access to its agricultural market, which is an absolute prerequisite to moving ahead. We all know the path to cutting manufactured goods barriers goes through agriculture.

Work still ahead

We are left with a lot of heavy lifting ahead, and we are going to redouble our efforts to get a final agreement that will slash trade barriers blocking manufactured goods. Manufactured goods are 75% of world trade, and we need a realization that cutting industrial trade barriers is an essential part of a comprehensive Doha Round Agreement.

One way of contributing to this is the new alliance we just formed in Hong Kong among U.S., European, Australian, Canadian, New Zealand, Korean, and other manufacturers. We have joined together for the first time and agreed to develop a common approach and common strategy - and we intend to make our voice heard in the coming months.

Without a clear statement from the ministers that one goal of the Doha Round is to cut the tariffs that are applied on manufactured goods, the existing disagreement is likely to continue. At the end of the day, will we get enough to make the deal worthwhile? There is no way to know yet, and we just have to keep trying.

Top Plant
The Top Plant program honors outstanding manufacturing facilities in North America.
Product of the Year
The Product of the Year program recognizes products newly released in the manufacturing industries.
System Integrator of the Year
Each year, a panel of Control Engineering and Plant Engineering editors and industry expert judges select the System Integrator of the Year Award winners in three categories.
October 2018
Tools vs. sensors, functional safety, compressor rental, an operational network of maintenance and safety
September 2018
2018 Engineering Leaders under 40, Women in Engineering, Six ways to reduce waste in manufacturing, and Four robot implementation challenges.
GAMS preview, 2018 Mid-Year Report, EAM and Safety
October 2018
2018 Product of the Year; Subsurface data methodologies; Digital twins; Well lifecycle data
August 2018
SCADA standardization, capital expenditures, data-driven drilling and execution
June 2018
Machine learning, produced water benefits, programming cavity pumps
Spring 2018
Burners for heat-treating furnaces, CHP, dryers, gas humidification, and more
October 2018
Complex upgrades for system integrators; Process control safety and compliance
September 2018
Effective process analytics; Four reasons why LTE networks are not IIoT ready

Annual Salary Survey

After two years of economic concerns, manufacturing leaders once again have homed in on the single biggest issue facing their operations:

It's the workers—or more specifically, the lack of workers.

The 2017 Plant Engineering Salary Survey looks at not just what plant managers make, but what they think. As they look across their plants today, plant managers say they don’t have the operational depth to take on the new technologies and new challenges of global manufacturing.

Read more: 2017 Salary Survey

The Maintenance and Reliability Coach's blog
Maintenance and reliability tips and best practices from the maintenance and reliability coaches at Allied Reliability Group.
One Voice for Manufacturing
The One Voice for Manufacturing blog reports on federal public policy issues impacting the manufacturing sector. One Voice is a joint effort by the National Tooling and Machining...
The Maintenance and Reliability Professionals Blog
The Society for Maintenance and Reliability Professionals an organization devoted...
Machine Safety
Join this ongoing discussion of machine guarding topics, including solutions assessments, regulatory compliance, gap analysis...
Research Analyst Blog
IMS Research, recently acquired by IHS Inc., is a leading independent supplier of market research and consultancy to the global electronics industry.
Marshall on Maintenance
Maintenance is not optional in manufacturing. It’s a profit center, driving productivity and uptime while reducing overall repair costs.
Lachance on CMMS
The Lachance on CMMS blog is about current maintenance topics. Blogger Paul Lachance is president and chief technology officer for Smartware Group.
Material Handling
This digital report explains how everything from conveyors and robots to automatic picking systems and digital orders have evolved to keep pace with the speed of change in the supply chain.
Electrical Safety Update
This digital report explains how plant engineers need to take greater care when it comes to electrical safety incidents on the plant floor.
IIoT: Machines, Equipment, & Asset Management
Articles in this digital report highlight technologies that enable Industrial Internet of Things, IIoT-related products and strategies.
Randy Steele
Maintenance Manager; California Oils Corp.
Matthew J. Woo, PE, RCDD, LEED AP BD+C
Associate, Electrical Engineering; Wood Harbinger
Randy Oliver
Control Systems Engineer; Robert Bosch Corp.
Data Centers: Impacts of Climate and Cooling Technology
This course focuses on climate analysis, appropriateness of cooling system selection, and combining cooling systems.
Safety First: Arc Flash 101
This course will help identify and reveal electrical hazards and identify the solutions to implementing and maintaining a safe work environment.
Critical Power: Hospital Electrical Systems
This course explains how maintaining power and communication systems through emergency power-generation systems is critical.
Design of Safe and Reliable Hydraulic Systems for Subsea Applications
This eGuide explains how the operation of hydraulic systems for subsea applications requires the user to consider additional aspects because of the unique conditions that apply to the setting
click me