Three reasons why wrench time is not a benchmarking tool

In this article, the author presents ciritcal issues and misunderstandings about wrench time.

10/10/2014


Wrench time and wrench time studies are two of the most misused, misunderstood, and painful to deal with elements of maintenance benchmarking for three reasons:

- Different definitions and standards
- Data that is skewed by the act of collection
- Overzealous comparisons of dissimilar metrics from different locations

We all like the implications of knowing the amount of non-value added work within our maintenance schedules and we would love to be able to measure and then trend the removal of non-value added time. This is a good thing, but let's look at what gets in the way and one thing to help improve our results for each challenge. The first struggle is around the definition or standard for wrench time. What is in? What is out? Is travel time part of wrench time? How much is too much? Is pre-work wrench time? Is trouble shooting wrench time? You need to answer these questions and more to get something standardized for your location. A good place to start is the SMRP Metric for wrench time but my guess is that you will need to add additional clarifications to make it relevant to your site.

The data is not accurate. By virtue of focusing on the data it changes the behaviors. If you tell me you are going to watch me type out this blog and count my mistypes I will by nature slow my typing and make less errors. The same thing happens when we do wrench time studies so the numbers we get will be different than actual. I suggest the use of something known as a DILO instead of typical stop watch time studies or other tool driven methods. In a DILO or Day In The Life Of you work with the craftsman to understand what gets in his way or what irritates him as he tries to complete his daily work. You are with him or her through their day learning based on their experiences. This approach is more about helping them and less about "watching and judging" them. In the end, you identify problems like missing permits, lost parts, and wrong tools and you see first had what that is costing them in time and patience without driving a wedge between parts of the organization. If you want to talk more about DILO send me an email and I will share with you tips and tricks based on my experience.

Some days it seems that everyone thinks they should compare their wrench time numbers to everyone else. This one is common for many metrics and KPIs but as I have suggested in the past it would be best if the sites looked at their ability to improve the metric and talked about what their delta over the last quarter was as opposed to the raw number. Then they could talk about the specific actions they have taken to get that delta. The raw metric are just too different in most cases to be compared and bad decisions can be made with bad data from bad comparisons.

Now I know I did not necessarily solve anything here but I hope I have provided a few ideas that might help as you calculated and evaluate your maintenance wrench time on your quest to reliability now.

Want more tips on reliability? Register for the SMRP Annual Conference, Oct. 20-23

For more information, visit www.reliabilitynow.net.

Shon is a certified maintenance and reliability professional. Shon specializes in business process management, adult education, strategic planning, organizational change management, leadership, and reliability engineering. Shon has been asked to speak at numerous professional conferences on these topics in the US as well as Europe, South America, and the Middle East.



Top Plant
The Top Plant program honors outstanding manufacturing facilities in North America.
Product of the Year
The Product of the Year program recognizes products newly released in the manufacturing industries.
System Integrator of the Year
Each year, a panel of Control Engineering and Plant Engineering editors and industry expert judges select the System Integrator of the Year Award winners in three categories.
October 2018
Tools vs. sensors, functional safety, compressor rental, an operational network of maintenance and safety
September 2018
2018 Engineering Leaders under 40, Women in Engineering, Six ways to reduce waste in manufacturing, and Four robot implementation challenges.
July/Aug
GAMS preview, 2018 Mid-Year Report, EAM and Safety
October 2018
2018 Product of the Year; Subsurface data methodologies; Digital twins; Well lifecycle data
August 2018
SCADA standardization, capital expenditures, data-driven drilling and execution
June 2018
Machine learning, produced water benefits, programming cavity pumps
Spring 2018
Burners for heat-treating furnaces, CHP, dryers, gas humidification, and more
October 2018
Complex upgrades for system integrators; Process control safety and compliance
September 2018
Effective process analytics; Four reasons why LTE networks are not IIoT ready

Annual Salary Survey

After two years of economic concerns, manufacturing leaders once again have homed in on the single biggest issue facing their operations:

It's the workers—or more specifically, the lack of workers.

The 2017 Plant Engineering Salary Survey looks at not just what plant managers make, but what they think. As they look across their plants today, plant managers say they don’t have the operational depth to take on the new technologies and new challenges of global manufacturing.

Read more: 2017 Salary Survey

The Maintenance and Reliability Coach's blog
Maintenance and reliability tips and best practices from the maintenance and reliability coaches at Allied Reliability Group.
One Voice for Manufacturing
The One Voice for Manufacturing blog reports on federal public policy issues impacting the manufacturing sector. One Voice is a joint effort by the National Tooling and Machining...
The Maintenance and Reliability Professionals Blog
The Society for Maintenance and Reliability Professionals an organization devoted...
Machine Safety
Join this ongoing discussion of machine guarding topics, including solutions assessments, regulatory compliance, gap analysis...
Research Analyst Blog
IMS Research, recently acquired by IHS Inc., is a leading independent supplier of market research and consultancy to the global electronics industry.
Marshall on Maintenance
Maintenance is not optional in manufacturing. It’s a profit center, driving productivity and uptime while reducing overall repair costs.
Lachance on CMMS
The Lachance on CMMS blog is about current maintenance topics. Blogger Paul Lachance is president and chief technology officer for Smartware Group.
Material Handling
This digital report explains how everything from conveyors and robots to automatic picking systems and digital orders have evolved to keep pace with the speed of change in the supply chain.
Electrical Safety Update
This digital report explains how plant engineers need to take greater care when it comes to electrical safety incidents on the plant floor.
IIoT: Machines, Equipment, & Asset Management
Articles in this digital report highlight technologies that enable Industrial Internet of Things, IIoT-related products and strategies.
Randy Steele
Maintenance Manager; California Oils Corp.
Matthew J. Woo, PE, RCDD, LEED AP BD+C
Associate, Electrical Engineering; Wood Harbinger
Randy Oliver
Control Systems Engineer; Robert Bosch Corp.
Data Centers: Impacts of Climate and Cooling Technology
This course focuses on climate analysis, appropriateness of cooling system selection, and combining cooling systems.
Safety First: Arc Flash 101
This course will help identify and reveal electrical hazards and identify the solutions to implementing and maintaining a safe work environment.
Critical Power: Hospital Electrical Systems
This course explains how maintaining power and communication systems through emergency power-generation systems is critical.
Design of Safe and Reliable Hydraulic Systems for Subsea Applications
This eGuide explains how the operation of hydraulic systems for subsea applications requires the user to consider additional aspects because of the unique conditions that apply to the setting
click me