Readers make noise about noise

In your December 1997 Human Side of Engineering article, "Is Hearing Loss Due to Job Noise Compensable?," I believe that the company involved is making a serious mistake if they simply "reassign him and hope that's the end of it.

02/01/1998


In your December 1997 Human Side of Engineering article, "Is Hearing Loss Due to Job Noise Compensable?," I believe that the company involved is making a serious mistake if they simply "reassign him and hope that's the end of it." Hearing loss is a very serious issue at most companies, and any employer that ignores a clear warning like this one does so at its peril. The fact that none of the other people that work blasting regularly have complained does not mean that they are not suffering hearing loss.

Once the company is forced to confront the problem, either by a lawsuit or OSHA citation, they will have to institute a hearing conservation program. This program involves baseline testing of the hearing of affected employees and periodic retesting, sound level measurements to determine the decibel exposure of the employees, and a program that ensures that employees are issued appropriate hearing protection and that its use is enforced.

If the company fails to maintain the program, then the company may be required to institute "engineered solutions" that eliminate the noise at the source. Good luck trying to come up with a way to hold the noise of a blasting operation below 80 decibels!

To say that, "It doesn't follow automatically that because Joe's hearing is adversely affected others would be too, or to the same extent as Joe's," ignores the fact that their hearing could be affected and the company is now aware that a potential problem exists. The responsible thing to do, and the way to stay out of trouble, is to determine whether the noise of the blasting is so intense that some employees may be going deaf and then take steps to protect their hearing.

-- Don Scribner

...more

Thorne's decision, "Let's reassign him and hope that's the end of it," was completely inappropriate. In my opinion, the responsible steps would have been:

1. Perform decimeter/noise level samplings of the Blasting Room operation

2. Use OSHA standards to determine the acceptable exposure levels, compared to the readings

3. Provide appropriate levels of protection from exposure and REQUIRE that they be utilized

4. Provide hearing tests for the employees subjected to the noise from the operation, to establish a baseline

5. Schedule and perform annual hearing tests to determine if hearing loss levels, compared with the baseline and subsequent testing, are progressing at a greater than normal rate, (and if the loss) could be attributed to industrial exposures.

Businesses today commonly find themselves responsible for conditions of which they were unaware. In this case, the company has been given the "gift" of an opportunity to mitigate a potentially litigious condition. The problem should be addressed at the source. Perhaps no real problem exists, but there is no evidence to support that contention. But if the potential exists for one employee, it exists for many. Anybody remember asbestos?

-- Charles V. Sanders, Principal Engineer, Boeing, Monrovia, CA





Top Plant
The Top Plant program honors outstanding manufacturing facilities in North America.
Product of the Year
The Product of the Year program recognizes products newly released in the manufacturing industries.
System Integrator of the Year
Each year, a panel of Control Engineering and Plant Engineering editors and industry expert judges select the System Integrator of the Year Award winners in three categories.
June 2018
2018 Lubrication Guide, Motor and maintenance management, Control system migration
May 2018
Electrical standards, robots and Lean manufacturing, and how an aluminum packaging plant is helping community growth.
April 2018
2017 Product of the Year winners, retrofitting a press, IMTS and Hannover Messe preview, natural refrigerants, testing steam traps
June 2018
Machine learning, produced water benefits, programming cavity pumps
April 2018
ROVs, rigs, and the real time; wellsite valve manifolds; AI on a chip; analytics use for pipelines
February 2018
Focus on power systems, process safety, electrical and power systems, edge computing in the oil & gas industry
Spring 2018
Burners for heat-treating furnaces, CHP, dryers, gas humidification, and more
April 2018
Implementing a DCS, stepper motors, intelligent motion control, remote monitoring of irrigation systems
February 2018
Setting internal automation standards

Annual Salary Survey

After two years of economic concerns, manufacturing leaders once again have homed in on the single biggest issue facing their operations:

It's the workers—or more specifically, the lack of workers.

The 2017 Plant Engineering Salary Survey looks at not just what plant managers make, but what they think. As they look across their plants today, plant managers say they don’t have the operational depth to take on the new technologies and new challenges of global manufacturing.

Read more: 2017 Salary Survey

The Maintenance and Reliability Coach's blog
Maintenance and reliability tips and best practices from the maintenance and reliability coaches at Allied Reliability Group.
One Voice for Manufacturing
The One Voice for Manufacturing blog reports on federal public policy issues impacting the manufacturing sector. One Voice is a joint effort by the National Tooling and Machining...
The Maintenance and Reliability Professionals Blog
The Society for Maintenance and Reliability Professionals an organization devoted...
Machine Safety
Join this ongoing discussion of machine guarding topics, including solutions assessments, regulatory compliance, gap analysis...
Research Analyst Blog
IMS Research, recently acquired by IHS Inc., is a leading independent supplier of market research and consultancy to the global electronics industry.
Marshall on Maintenance
Maintenance is not optional in manufacturing. It’s a profit center, driving productivity and uptime while reducing overall repair costs.
Lachance on CMMS
The Lachance on CMMS blog is about current maintenance topics. Blogger Paul Lachance is president and chief technology officer for Smartware Group.
Electrical Safety Update
This digital report explains how plant engineers need to take greater care when it comes to electrical safety incidents on the plant floor.
Maintenance & Safety
The maintenance journey has been a long, slow trek for most manufacturers and has gone from preventive maintenance to predictive maintenance.
IIoT: Machines, Equipment, & Asset Management
Articles in this digital report highlight technologies that enable Industrial Internet of Things, IIoT-related products and strategies.
Randy Steele
Maintenance Manager; California Oils Corp.
Matthew J. Woo, PE, RCDD, LEED AP BD+C
Associate, Electrical Engineering; Wood Harbinger
Randy Oliver
Control Systems Engineer; Robert Bosch Corp.
Data Centers: Impacts of Climate and Cooling Technology
This course focuses on climate analysis, appropriateness of cooling system selection, and combining cooling systems.
Safety First: Arc Flash 101
This course will help identify and reveal electrical hazards and identify the solutions to implementing and maintaining a safe work environment.
Critical Power: Hospital Electrical Systems
This course explains how maintaining power and communication systems through emergency power-generation systems is critical.
click me