ReaderForum

Wax warning In the "Simple Solutions" section of the July 2000 issue, the suggestion for using floor wax on the threads of aluminum conduit is a violation of the 1999 National Electric Code.

10/01/2000


Wax warning

In the "Simple Solutions" section of the July 2000 issue, the suggestion for using floor wax on the threads of aluminum conduit is a violation of the 1999 National Electric Code. Section 110-2 requires items to be approved for the use. Section 110-3 sets out guidelines for this approval.

Aluminum conduit is approved for use as an equipment grounding conductor, and the use of wax on the threads could compromise the joint, no longer maintaining the electrical continuity of the system, and also affecting the bonding requirements for conduit. Grounding and bonding are covered in section 250 of the Code.

The use of wax on the threads can also permit overtightening of the joint, thus weakening fittings, causing them to split and break. The floor wax could also harden and seal the threads, which would represent a problem if used in a hazardous classified area. Threads on fittings are designed to allow explosive gases to escape in the case of an explosion inside the enclosure or conduit. Gases are cooled so that by the time they get out into the raceways, they will not cause a fire or explosion there. If threads are sealed, conduit and enclosures may turn into pipe bombs.

The local electrical supply store should be able to offer a lubricant approved for this purpose. It must be remembered that if a lubricant is used, the installer must be careful not to overtighten the joints.-Mike Hunsaker, Maintenance Coordinator, Thiokol Propulsion, Brigham City, UT

Tip contributor's reply: Mr. Hunsaker makes some good points. As far as the floor wax compromising the grounding of the conduit, it is common knowledge that when you tighten conduit, the threads eat right through the wax and into the aluminum, which is why I suggested wax in the first place. The threads become hot and the aluminum seizes and you cannot screw the pipes all the way together.

As far as overtightening the conduit, you can do that with or without the wax. Common sense has to come into play.

The point about a pipe bomb doesn't hold up. Have you ever heard of an aluminum pipe bomb? No, because it splits before it fragments. If using aluminum conduit, or any conduit in a hazardous location, there are sealoff fittings no farther away than 18-in. before any box or spark creating device, and the box and/or switch are explosionproof to keep the spark from getting into the hazardous area. The spark should not go into the conduit either. If the conduit run is large, say 500 MCM and at 480 V, 300 amps, and the conductors short to the conduit or together inside the conduit, you will blow a hole in the aluminum with or without the wax because the aluminum melting point is less than regular rigid conduit, which will probably do the same thing.-Dave White, Titan Intl., Inc., Quincy, IL

 

Focus on training

As a former plant operator, turned training instructor, I think your Editorial, "The wheels are coming loose" (PE, July 2000, p 12), is right on the mark.

Serious problems develop when personnel are not specifically trained in all areas of plant responsibilities. Every time we read about an accident or other catastrophe in a plant operation, it can almost always be linked to a lack of communication and training.

The Gulf Coast Process Technology Alliance is trying to correct this problem. This group of industry members and educational institutions are working together to standardize training for plant personnel. Find out more at www.

processtech.org/gcptahome.htm.-Martha McKinley, Eastman Chemical Co.





Top Plant
The Top Plant program honors outstanding manufacturing facilities in North America.
Product of the Year
The Product of the Year program recognizes products newly released in the manufacturing industries.
System Integrator of the Year
Each year, a panel of Control Engineering and Plant Engineering editors and industry expert judges select the System Integrator of the Year Award winners in three categories.
September 2018
2018 Engineering Leaders under 40, Women in Engineering, Six ways to reduce waste in manufacturing, and Four robot implementation challenges.
July/Aug
GAMS preview, 2018 Mid-Year Report, EAM and Safety
June 2018
2018 Lubrication Guide, Motor and maintenance management, Control system migration
August 2018
SCADA standardization, capital expenditures, data-driven drilling and execution
June 2018
Machine learning, produced water benefits, programming cavity pumps
April 2018
ROVs, rigs, and the real time; wellsite valve manifolds; AI on a chip; analytics use for pipelines
Spring 2018
Burners for heat-treating furnaces, CHP, dryers, gas humidification, and more
August 2018
Choosing an automation controller, Lean manufacturing
September 2018
Effective process analytics; Four reasons why LTE networks are not IIoT ready

Annual Salary Survey

After two years of economic concerns, manufacturing leaders once again have homed in on the single biggest issue facing their operations:

It's the workers—or more specifically, the lack of workers.

The 2017 Plant Engineering Salary Survey looks at not just what plant managers make, but what they think. As they look across their plants today, plant managers say they don’t have the operational depth to take on the new technologies and new challenges of global manufacturing.

Read more: 2017 Salary Survey

The Maintenance and Reliability Coach's blog
Maintenance and reliability tips and best practices from the maintenance and reliability coaches at Allied Reliability Group.
One Voice for Manufacturing
The One Voice for Manufacturing blog reports on federal public policy issues impacting the manufacturing sector. One Voice is a joint effort by the National Tooling and Machining...
The Maintenance and Reliability Professionals Blog
The Society for Maintenance and Reliability Professionals an organization devoted...
Machine Safety
Join this ongoing discussion of machine guarding topics, including solutions assessments, regulatory compliance, gap analysis...
Research Analyst Blog
IMS Research, recently acquired by IHS Inc., is a leading independent supplier of market research and consultancy to the global electronics industry.
Marshall on Maintenance
Maintenance is not optional in manufacturing. It’s a profit center, driving productivity and uptime while reducing overall repair costs.
Lachance on CMMS
The Lachance on CMMS blog is about current maintenance topics. Blogger Paul Lachance is president and chief technology officer for Smartware Group.
Material Handling
This digital report explains how everything from conveyors and robots to automatic picking systems and digital orders have evolved to keep pace with the speed of change in the supply chain.
Electrical Safety Update
This digital report explains how plant engineers need to take greater care when it comes to electrical safety incidents on the plant floor.
IIoT: Machines, Equipment, & Asset Management
Articles in this digital report highlight technologies that enable Industrial Internet of Things, IIoT-related products and strategies.
Randy Steele
Maintenance Manager; California Oils Corp.
Matthew J. Woo, PE, RCDD, LEED AP BD+C
Associate, Electrical Engineering; Wood Harbinger
Randy Oliver
Control Systems Engineer; Robert Bosch Corp.
Data Centers: Impacts of Climate and Cooling Technology
This course focuses on climate analysis, appropriateness of cooling system selection, and combining cooling systems.
Safety First: Arc Flash 101
This course will help identify and reveal electrical hazards and identify the solutions to implementing and maintaining a safe work environment.
Critical Power: Hospital Electrical Systems
This course explains how maintaining power and communication systems through emergency power-generation systems is critical.
Design of Safe and Reliable Hydraulic Systems for Subsea Applications
This eGuide explains how the operation of hydraulic systems for subsea applications requires the user to consider additional aspects because of the unique conditions that apply to the setting
click me