Machinery production slows as economic uncertainty continues

Worldwide growth in machinery production stood at 6.3% in 2012, more than 10 percentage points lower than the previous year.

02/01/2013


IMS Research (acquired by IHS, Inc.)The continued global economic slowdown has had a severe impact on worldwide machinery production, with growth in all regions falling significantly in 2012 compared with 2011. According to the new Machinery Production Report from IMS Research (acquired by IHS, Inc.) worldwide growth in machinery production stood at 6.3% in 2012, more than 10 percentage points lower than the previous year.

Asia Pacific has coped best through the period of global economic turbulence, and has continued to grow faster than any other region. Even China, though, has seen growth in machinery output fall – down to an estimated 9.1% in 2012 (compared with 19.9% in 2011) – as a result of the weakening demand from a struggling Europe and shifting domestic monetary policies. Although this is the slowest rate of increase seen in many years, it still makes China one of the fastest growing nations.

Meanwhile, in Europe, the continued economic uncertainty has taken its toll. Sovereign debt problems, high unemployment and falling exports have meant that economic growth has been slow at best throughout most of Europe. For the region overall, GDP in 2012 stood at less than 1.0%, and is projected to remain as such throughout 2013, with several countries (including Belgium, France, Italy, Portugal and Spain)  expected to see declines in both years. Although machinery production is expected to outperform GDP, this backdrop is not one conducive to strong investment from Europe’s manufactures. Demand from better-performing economies, such as Asia and Eastern Europe, is not enough to prop up weak demand from the bigger Western European nations. Currently, the machinery production growth rate for Europe is forecast to be 3.5% in 2013, some way behind the 9.4% forecast for Asia Pacific. The Americas has fared reasonably well in contrast to Europe, growing 7.6% in 2012; rather faster than the 4.2% seen in Europe; within this, wind turbine production was amongst the best performing sectors, increasing by an estimated 18.7%. 

Within machinery production, there was significant variation between the different sectors. The semiconductor equipment sector, which is a notoriously cyclical industry, saw steep declines in 2012; so too did photovoltaic (PV) manufacturing equipment, suffering as a result of significant over capacity. Agricultural machinery, on the other hand, has held up reasonably well, supported by strong commodity prices, indicating that amongst the uncertainty there remains areas of optimism.

Source: IMS Research



Top Plant
The Top Plant program honors outstanding manufacturing facilities in North America.
Product of the Year
The Product of the Year program recognizes products newly released in the manufacturing industries.
System Integrator of the Year
Each year, a panel of Control Engineering and Plant Engineering editors and industry expert judges select the System Integrator of the Year Award winners in three categories.
September 2018
2018 Engineering Leaders under 40, Women in Engineering, Six ways to reduce waste in manufacturing, and Four robot implementation challenges.
July/Aug
GAMS preview, 2018 Mid-Year Report, EAM and Safety
June 2018
2018 Lubrication Guide, Motor and maintenance management, Control system migration
August 2018
SCADA standardization, capital expenditures, data-driven drilling and execution
June 2018
Machine learning, produced water benefits, programming cavity pumps
April 2018
ROVs, rigs, and the real time; wellsite valve manifolds; AI on a chip; analytics use for pipelines
Spring 2018
Burners for heat-treating furnaces, CHP, dryers, gas humidification, and more
August 2018
Choosing an automation controller, Lean manufacturing
September 2018
Effective process analytics; Four reasons why LTE networks are not IIoT ready

Annual Salary Survey

After two years of economic concerns, manufacturing leaders once again have homed in on the single biggest issue facing their operations:

It's the workers—or more specifically, the lack of workers.

The 2017 Plant Engineering Salary Survey looks at not just what plant managers make, but what they think. As they look across their plants today, plant managers say they don’t have the operational depth to take on the new technologies and new challenges of global manufacturing.

Read more: 2017 Salary Survey

The Maintenance and Reliability Coach's blog
Maintenance and reliability tips and best practices from the maintenance and reliability coaches at Allied Reliability Group.
One Voice for Manufacturing
The One Voice for Manufacturing blog reports on federal public policy issues impacting the manufacturing sector. One Voice is a joint effort by the National Tooling and Machining...
The Maintenance and Reliability Professionals Blog
The Society for Maintenance and Reliability Professionals an organization devoted...
Machine Safety
Join this ongoing discussion of machine guarding topics, including solutions assessments, regulatory compliance, gap analysis...
Research Analyst Blog
IMS Research, recently acquired by IHS Inc., is a leading independent supplier of market research and consultancy to the global electronics industry.
Marshall on Maintenance
Maintenance is not optional in manufacturing. It’s a profit center, driving productivity and uptime while reducing overall repair costs.
Lachance on CMMS
The Lachance on CMMS blog is about current maintenance topics. Blogger Paul Lachance is president and chief technology officer for Smartware Group.
Material Handling
This digital report explains how everything from conveyors and robots to automatic picking systems and digital orders have evolved to keep pace with the speed of change in the supply chain.
Electrical Safety Update
This digital report explains how plant engineers need to take greater care when it comes to electrical safety incidents on the plant floor.
IIoT: Machines, Equipment, & Asset Management
Articles in this digital report highlight technologies that enable Industrial Internet of Things, IIoT-related products and strategies.
Randy Steele
Maintenance Manager; California Oils Corp.
Matthew J. Woo, PE, RCDD, LEED AP BD+C
Associate, Electrical Engineering; Wood Harbinger
Randy Oliver
Control Systems Engineer; Robert Bosch Corp.
Data Centers: Impacts of Climate and Cooling Technology
This course focuses on climate analysis, appropriateness of cooling system selection, and combining cooling systems.
Safety First: Arc Flash 101
This course will help identify and reveal electrical hazards and identify the solutions to implementing and maintaining a safe work environment.
Critical Power: Hospital Electrical Systems
This course explains how maintaining power and communication systems through emergency power-generation systems is critical.
Design of Safe and Reliable Hydraulic Systems for Subsea Applications
This eGuide explains how the operation of hydraulic systems for subsea applications requires the user to consider additional aspects because of the unique conditions that apply to the setting
click me