Kevin Parker: Innovation as a collective undertaking applied to newly pervasive technologies

Why is innovation the current king of management concepts? How has it become in manufacturing circles something akin to one of the “four big truths” or “five shining lights” that used to emerge with the five-year plans of command economies? According to Paths of Innovation: Technological Change in 20th Century America, by Mowery and Rosenburg, it wasn't till the second h...

04/01/2008


Why is innovation the current king of management concepts? How has it become in manufacturing circles something akin to one of the “four big truths” or “five shining lights” that used to emerge with the five-year plans of command economies?

According to Paths of Innovation: Technological Change in 20th Century America , by Mowery and Rosenburg, it wasn't till the second half of that century that economists fully appreciated “the extent to which economic growth was a consequence of the process of technological change.” As proof, studies show only a relatively small percentage of measured output in the late 19th and early 20th century as accounted for by growth in measured inputs of capital and labor.

While technological change undoubtedly accounts for much of the additional output growth, its impact, unfortunately, doesn't last, as new products and industries “experience retardation in their growth rates as their markets reach saturation… and further cost-reducing process innovations have relatively small effects on demand,” the cited studies demonstrate.

Does that mean then, that product innovation, as opposed to process innovation, is always the key to success?

Not necessarily, as the always helpful Wikipedia points out in its entry on “innovation”: process innovation can lead directly to increased shareholder value. Product innovation, on the other hand, risks costly R&D efforts that, if they fail, can erode shareholder value.

Mowery and Rosenburg themselves feel the studies underestimate “the importance of the adoption of new technologies by mature industries.” And they point out it's hard to untangle all the threads involved, because of globalization.

It's become a cliche to point out that—measured by share of gross national product accounted for by exports—the U.S. economy 1900 to 1910 was more open than any time from 1910 to 1970. But the last third of the 20th century saw “an increasingly dense network of inter-firm relationships… that contribute to more rapid international flows of technology…. The spectacular improvements in the information technologies that unite this international network have lent to the term 'globalization' a vastly expanded significance over its meaning at the beginning of the century.”

It's wrong also, the authors say, to think innovation only arises from fundamental research at the frontiers of science or even the institutionalization of innovation as “R&D,” but rather often draws on “existing technological knowledge.”

Perhaps that's why innovation discussions find an audience, despite that relatively few executives, managers, or knowledge professionals are directly engaged in R&D or design efforts. New technologies are so quickly pervasive it's as if we're all engaged in some grand exercise to learn how to best apply them.

No one, for example, has ever been identified as the inventor of the generic engineering and production systems used in manufacturing enterprises today. Yet, while infinitely varied in detail, basic system elements are common around the world.

Innovation discussions speak to us because we're all part of a collective effort to find best uses for new technologies that have come into our lives in the last twenty years, applying them in ever finer granularity of detail to a heritage of processes that must change in light of the evolving technology infrastructure.





Top Plant
The Top Plant program honors outstanding manufacturing facilities in North America.
Product of the Year
The Product of the Year program recognizes products newly released in the manufacturing industries.
System Integrator of the Year
Each year, a panel of Control Engineering and Plant Engineering editors and industry expert judges select the System Integrator of the Year Award winners in three categories.
September 2018
2018 Engineering Leaders under 40, Women in Engineering, Six ways to reduce waste in manufacturing, and Four robot implementation challenges.
July/Aug
GAMS preview, 2018 Mid-Year Report, EAM and Safety
June 2018
2018 Lubrication Guide, Motor and maintenance management, Control system migration
August 2018
SCADA standardization, capital expenditures, data-driven drilling and execution
June 2018
Machine learning, produced water benefits, programming cavity pumps
April 2018
ROVs, rigs, and the real time; wellsite valve manifolds; AI on a chip; analytics use for pipelines
Spring 2018
Burners for heat-treating furnaces, CHP, dryers, gas humidification, and more
August 2018
Choosing an automation controller, Lean manufacturing
September 2018
Effective process analytics; Four reasons why LTE networks are not IIoT ready

Annual Salary Survey

After two years of economic concerns, manufacturing leaders once again have homed in on the single biggest issue facing their operations:

It's the workers—or more specifically, the lack of workers.

The 2017 Plant Engineering Salary Survey looks at not just what plant managers make, but what they think. As they look across their plants today, plant managers say they don’t have the operational depth to take on the new technologies and new challenges of global manufacturing.

Read more: 2017 Salary Survey

The Maintenance and Reliability Coach's blog
Maintenance and reliability tips and best practices from the maintenance and reliability coaches at Allied Reliability Group.
One Voice for Manufacturing
The One Voice for Manufacturing blog reports on federal public policy issues impacting the manufacturing sector. One Voice is a joint effort by the National Tooling and Machining...
The Maintenance and Reliability Professionals Blog
The Society for Maintenance and Reliability Professionals an organization devoted...
Machine Safety
Join this ongoing discussion of machine guarding topics, including solutions assessments, regulatory compliance, gap analysis...
Research Analyst Blog
IMS Research, recently acquired by IHS Inc., is a leading independent supplier of market research and consultancy to the global electronics industry.
Marshall on Maintenance
Maintenance is not optional in manufacturing. It’s a profit center, driving productivity and uptime while reducing overall repair costs.
Lachance on CMMS
The Lachance on CMMS blog is about current maintenance topics. Blogger Paul Lachance is president and chief technology officer for Smartware Group.
Material Handling
This digital report explains how everything from conveyors and robots to automatic picking systems and digital orders have evolved to keep pace with the speed of change in the supply chain.
Electrical Safety Update
This digital report explains how plant engineers need to take greater care when it comes to electrical safety incidents on the plant floor.
IIoT: Machines, Equipment, & Asset Management
Articles in this digital report highlight technologies that enable Industrial Internet of Things, IIoT-related products and strategies.
Randy Steele
Maintenance Manager; California Oils Corp.
Matthew J. Woo, PE, RCDD, LEED AP BD+C
Associate, Electrical Engineering; Wood Harbinger
Randy Oliver
Control Systems Engineer; Robert Bosch Corp.
Data Centers: Impacts of Climate and Cooling Technology
This course focuses on climate analysis, appropriateness of cooling system selection, and combining cooling systems.
Safety First: Arc Flash 101
This course will help identify and reveal electrical hazards and identify the solutions to implementing and maintaining a safe work environment.
Critical Power: Hospital Electrical Systems
This course explains how maintaining power and communication systems through emergency power-generation systems is critical.
Design of Safe and Reliable Hydraulic Systems for Subsea Applications
This eGuide explains how the operation of hydraulic systems for subsea applications requires the user to consider additional aspects because of the unique conditions that apply to the setting
click me