It's 'sluggish,' but manufacturing's global recovery moves forward

Recent data paint an unmistakable picture that a global economic recovery is in progress. Yet it does so with a caveat that the rebound could be unusually sluggish and disproportionately catalyzed by a number of select emerging market nations, notably China, India and Brazil, which were less affected than the industrialized countries by the global financial crisis, according to a new report.

11/01/2009


Recent data paint an unmistakable picture that a global economic recovery is in progress. Yet it does so with a caveat that the rebound could be unusually sluggish and disproportionately catalyzed by a number of select emerging market nations, notably China, India and Brazil, which were less affected than the industrialized countries by the global financial crisis, according to a new report.

In the MAPI Quarterly Forecast of U.S. Exports, Global Growth, and the Dollar: Fourth Quarter 2009 Through Fourth Quarter 2011, economist Cliff Waldman writes that “signs of normalization continue to appear in the financial and economic environments,” and that the foundations for a renewed period of global growth are increasingly evident as the world pivots from crisis to at least some semblance of stability.

“Unfortunately, stability does not necessarily presage strength,” Waldman cautioned. “Two factors in particular are likely to slow the pace of the recovery during the next few years. First, the timing and impact of the withdrawal of historically accommodative monetary and fiscal policies is a tricky issue, as near-zero interest rate policies are unsustainable. Second, it would appear that the U.S. consumer has been financially shocked into a higher savings rate, a positive development for long-run global stability, but one that saps a key source of U.S. and global strength just when it is needed to help pull the world economy out of an especially difficult period.”

A falling dollar and only modest global growth tempers MAPI's exports forecast. MAPI anticipates the growth rate of total U.S. exports of goods and services will contract by 11.8% in 2009. This will be followed by 5.7% growth in 2010, with acceleration to 7.9% in 2011, a rebound tepid by the standards of recoveries from deep export contractions in the post-World War II period.

Most advanced economies are expected to experience marginal recoveries in gross domestic product (GDP) and in manufacturing output over the next two years. GDP in non-U.S. industrialized countries, which include Canada, the Eurozone (plus Denmark, the United Kingdom and Sweden) and Japan, is expected to rise incrementally from 1.9% growth during the first quarter of 2010 to an average of 2.6% growth in the second half of 2011.

Developing countries, as has been the case in recent decades, will likely grow at a faster pace. Aggregate developing country GDP is expected to increase by 3.5% during the first quarter of 2010, and then gradually reach a high of 5% growth during the third quarter of 2011 before moderating to 4.5% growth by the end of 2011.





Top Plant
The Top Plant program honors outstanding manufacturing facilities in North America. View the 2017 Top Plant.
Product of the Year
The Product of the Year program recognizes products newly released in the manufacturing industries.
System Integrator of the Year
Each year, a panel of Control Engineering and Plant Engineering editors and industry expert judges select the System Integrator of the Year Award winners in three categories.
February 2018
2017 Product of the Year winners, retrofitting a press, IMTS and Hannover Messe preview, natural refrigerants, testing steam traps
March 2018
SCCR, 2018 Maintenance study, and VFDs in a washdown environment.
Jan/Feb 2018
Welding ergonomics, 2017 Salary Survey, and surge protection
April 2018
ROVs, rigs, and the real time; wellsite valve manifolds; AI on a chip; analytics use for pipelines
February 2018
Focus on power systems, process safety, electrical and power systems, edge computing in the oil & gas industry
December 2017
Product of the Year winners, Pattern recognition, Engineering analytics, Revitalize older pump installations
April 2018
Implementing a DCS, stepper motors, intelligent motion control, remote monitoring of irrigation systems
February 2018
Setting internal automation standards
December 2017
PID controllers, Solar-powered SCADA, Using 80 GHz radar sensors

Annual Salary Survey

Before the calendar turned, 2016 already had the makings of a pivotal year for manufacturing, and for the world.

There were the big events for the year, including the United States as Partner Country at Hannover Messe in April and the 2016 International Manufacturing Technology Show in Chicago in September. There's also the matter of the U.S. presidential elections in November, which promise to shape policy in manufacturing for years to come.

But the year started with global economic turmoil, as a slowdown in Chinese manufacturing triggered a worldwide stock hiccup that sent values plummeting. The continued plunge in world oil prices has resulted in a slowdown in exploration and, by extension, the manufacture of exploration equipment.

Read more: 2015 Salary Survey

The Maintenance and Reliability Coach's blog
Maintenance and reliability tips and best practices from the maintenance and reliability coaches at Allied Reliability Group.
One Voice for Manufacturing
The One Voice for Manufacturing blog reports on federal public policy issues impacting the manufacturing sector. One Voice is a joint effort by the National Tooling and Machining...
The Maintenance and Reliability Professionals Blog
The Society for Maintenance and Reliability Professionals an organization devoted...
Machine Safety
Join this ongoing discussion of machine guarding topics, including solutions assessments, regulatory compliance, gap analysis...
Research Analyst Blog
IMS Research, recently acquired by IHS Inc., is a leading independent supplier of market research and consultancy to the global electronics industry.
Marshall on Maintenance
Maintenance is not optional in manufacturing. It’s a profit center, driving productivity and uptime while reducing overall repair costs.
Lachance on CMMS
The Lachance on CMMS blog is about current maintenance topics. Blogger Paul Lachance is president and chief technology officer for Smartware Group.
Maintenance & Safety
The maintenance journey has been a long, slow trek for most manufacturers and has gone from preventive maintenance to predictive maintenance.
Industrial Analytics
This digital report explains how plant engineers and subject matter experts (SME) need support for time series data and its many challenges.
IIoT: Operations & IT
This digital report will explore several aspects of how IIoT will transform manufacturing in the coming years.
Randy Steele
Maintenance Manager; California Oils Corp.
Matthew J. Woo, PE, RCDD, LEED AP BD+C
Associate, Electrical Engineering; Wood Harbinger
Randy Oliver
Control Systems Engineer; Robert Bosch Corp.
Data Centers: Impacts of Climate and Cooling Technology
This course focuses on climate analysis, appropriateness of cooling system selection, and combining cooling systems.
Safety First: Arc Flash 101
This course will help identify and reveal electrical hazards and identify the solutions to implementing and maintaining a safe work environment.
Critical Power: Hospital Electrical Systems
This course explains how maintaining power and communication systems through emergency power-generation systems is critical.
click me