It's "sluggish" but global recovery moves forward

MAPI forecast shows slow steps as investors display caution

10/27/2009


Recent data paint an unmistakable picture that a global economic recovery is in progress. Yet it does so with a caveat that the rebound could be unusually sluggish and disproportionately catalyzed by a number of select emerging market nations, notably China, India, and Brazil, which were less affected than the industrialized countries by the global financial crisis, according to a new report.
In the MAPI Quarterly Forecast of U.S. Exports , Global Growth, and the Dollar: Fourth Quarter 2009 Through Fourth Quarter 2011, economist Cliff Waldman writes that "signs of normalization continue to appear in the financial and economic environments," and that the foundations for a renewed period of global growth are increasingly evident as the world pivots from crisis to at least some semblance of stability.
"Unfortunately, stability does not necessarily presage strength," Waldman cautioned. "Two factors in particular are likely to slow the pace of the recovery during the next few years. First, the timing and impact of the withdrawal of historically accommodative monetary and fiscal policies is a tricky issue, as near-zero interest rate policies are unsustainable. Second, it would appear that the U.S. consumer has been financially shocked into a higher savings rate, a positive development for long-run global stability, but one that saps a key source of U.S. and global strength just when it is needed to help pull the world economy out of an especially difficult period."
A falling dollar and only modest global growth tempers MAPI's exports forecast. MAPI anticipates the growth rate of total U.S. exports of goods and services will contract by 11.8% in 2009. This will be followed by 5.7% growth in 2010, with acceleration to 7.9% in 2011, a rebound tepid by the standards of recoveries from deep export contractions in the post-World War II period.
Most advanced economies are expected to experience marginal recoveries in gross domestic product (GDP) and in manufacturing output over the next two years. GDP in non-U.S. industrialized countries, which include Canada, the Eurozone (plus Denmark, the United Kingdom, and Sweden), and Japan, is expected to rise incrementally from 1.9% growth during the first quarter of 2010 to an average of 2.6% growth in the second half of 2011.
Developing countries, as has been the case in recent decades, will likely grow at a faster pace. Aggregate developing country GDP is expected to increase by 3.5% during the first quarter of 2010, and then gradually reach a high of 5% growth during the third quarter of 2011 before moderating to 4.5% growth by the end of 2011.



Top Plant
The Top Plant program honors outstanding manufacturing facilities in North America.
Product of the Year
The Product of the Year program recognizes products newly released in the manufacturing industries.
System Integrator of the Year
Each year, a panel of Control Engineering and Plant Engineering editors and industry expert judges select the System Integrator of the Year Award winners in three categories.
October 2018
Tools vs. sensors, functional safety, compressor rental, an operational network of maintenance and safety
September 2018
2018 Engineering Leaders under 40, Women in Engineering, Six ways to reduce waste in manufacturing, and Four robot implementation challenges.
July/Aug
GAMS preview, 2018 Mid-Year Report, EAM and Safety
October 2018
2018 Product of the Year; Subsurface data methodologies; Digital twins; Well lifecycle data
August 2018
SCADA standardization, capital expenditures, data-driven drilling and execution
June 2018
Machine learning, produced water benefits, programming cavity pumps
Spring 2018
Burners for heat-treating furnaces, CHP, dryers, gas humidification, and more
October 2018
Complex upgrades for system integrators; Process control safety and compliance
September 2018
Effective process analytics; Four reasons why LTE networks are not IIoT ready

Annual Salary Survey

After two years of economic concerns, manufacturing leaders once again have homed in on the single biggest issue facing their operations:

It's the workers—or more specifically, the lack of workers.

The 2017 Plant Engineering Salary Survey looks at not just what plant managers make, but what they think. As they look across their plants today, plant managers say they don’t have the operational depth to take on the new technologies and new challenges of global manufacturing.

Read more: 2017 Salary Survey

The Maintenance and Reliability Coach's blog
Maintenance and reliability tips and best practices from the maintenance and reliability coaches at Allied Reliability Group.
One Voice for Manufacturing
The One Voice for Manufacturing blog reports on federal public policy issues impacting the manufacturing sector. One Voice is a joint effort by the National Tooling and Machining...
The Maintenance and Reliability Professionals Blog
The Society for Maintenance and Reliability Professionals an organization devoted...
Machine Safety
Join this ongoing discussion of machine guarding topics, including solutions assessments, regulatory compliance, gap analysis...
Research Analyst Blog
IMS Research, recently acquired by IHS Inc., is a leading independent supplier of market research and consultancy to the global electronics industry.
Marshall on Maintenance
Maintenance is not optional in manufacturing. It’s a profit center, driving productivity and uptime while reducing overall repair costs.
Lachance on CMMS
The Lachance on CMMS blog is about current maintenance topics. Blogger Paul Lachance is president and chief technology officer for Smartware Group.
Material Handling
This digital report explains how everything from conveyors and robots to automatic picking systems and digital orders have evolved to keep pace with the speed of change in the supply chain.
Electrical Safety Update
This digital report explains how plant engineers need to take greater care when it comes to electrical safety incidents on the plant floor.
IIoT: Machines, Equipment, & Asset Management
Articles in this digital report highlight technologies that enable Industrial Internet of Things, IIoT-related products and strategies.
Randy Steele
Maintenance Manager; California Oils Corp.
Matthew J. Woo, PE, RCDD, LEED AP BD+C
Associate, Electrical Engineering; Wood Harbinger
Randy Oliver
Control Systems Engineer; Robert Bosch Corp.
Data Centers: Impacts of Climate and Cooling Technology
This course focuses on climate analysis, appropriateness of cooling system selection, and combining cooling systems.
Safety First: Arc Flash 101
This course will help identify and reveal electrical hazards and identify the solutions to implementing and maintaining a safe work environment.
Critical Power: Hospital Electrical Systems
This course explains how maintaining power and communication systems through emergency power-generation systems is critical.
Design of Safe and Reliable Hydraulic Systems for Subsea Applications
This eGuide explains how the operation of hydraulic systems for subsea applications requires the user to consider additional aspects because of the unique conditions that apply to the setting
click me