Follow precedence when demoting an employee

Machine Repairman Grade II Ed Crowley was hired in June by Maintenance Supervisor Jack Andrews.

03/01/1998


Machine Repairman Grade II Ed Crowley was hired in June by Maintenance Supervisor Jack Andrews. Although his performance was marginal at best, he survived his 30-day probationary period only because the department was in a state of disruption, and Andrews was too busy or confused to monitor his work.

Crowley's performance continued to be marginal or worse. About 4 mo after his date of hire, Andrews resigned and was replaced by a new supervisor, Bill Shapper. Shapper was a good man, but it took him 2 mo or more to learn his job and become familiar with its requirements. At this point, he began to reorganize the maintenance department.

It was thus more than 6 mo before Shapper got around to reviewing Crowley's job sheets and performance.

He confided to his assistant, "This guy never should have been kept beyond his probationary period."

"I know, but that wasn't my decision to make."

"What to do with him now is the decision to make."

Shapper summoned Crowley to his desk and reviewed his performance record with him. Crowley had no comment to make.

"Ed, I'm sorry I have to do this, but I'm moving you a step down to Mechanic Grade II," Shapper said.

Crowley scowled. He knew this move entailed a lower wage rate and lower level work.

Crowley protested, "That's in violation of the labor agreement. The Manual states that prior to terminating or demoting an employee, remedial measures must be applied to improve his performance. I was never put into a training program or anything."

Shapper discussed Crowley's response with his assistant, who felt the employee might have a point. "The Manual does call for a Corrective Action Plan."

"The policy makes sense," Shapper said. "But it would be hopeless in Crowley's case. No way could his performance be improved. It would be a waste of money and time."

He put through the demotion notice. Crowley promptly responded by grieving.

Question : How do you rate Shapper's chance of making the demotion stick?

Plant engineer's decision: When Plant Engineer Carl Barcley was apprised of the details, he advised Shapper to rescind the demotion and enroll Crowley in a training program, with his future job classification dependent on the outcome.

"When procedures are preestablished for dealing with substandard performance, whether an employee is judged hopeless or not, you have no choice but to follow them."





Top Plant
The Top Plant program honors outstanding manufacturing facilities in North America.
Product of the Year
The Product of the Year program recognizes products newly released in the manufacturing industries.
System Integrator of the Year
Each year, a panel of Control Engineering and Plant Engineering editors and industry expert judges select the System Integrator of the Year Award winners in three categories.
September 2018
2018 Engineering Leaders under 40, Women in Engineering, Six ways to reduce waste in manufacturing, and Four robot implementation challenges.
July/Aug
GAMS preview, 2018 Mid-Year Report, EAM and Safety
June 2018
2018 Lubrication Guide, Motor and maintenance management, Control system migration
August 2018
SCADA standardization, capital expenditures, data-driven drilling and execution
June 2018
Machine learning, produced water benefits, programming cavity pumps
April 2018
ROVs, rigs, and the real time; wellsite valve manifolds; AI on a chip; analytics use for pipelines
Spring 2018
Burners for heat-treating furnaces, CHP, dryers, gas humidification, and more
August 2018
Choosing an automation controller, Lean manufacturing
September 2018
Effective process analytics; Four reasons why LTE networks are not IIoT ready

Annual Salary Survey

After two years of economic concerns, manufacturing leaders once again have homed in on the single biggest issue facing their operations:

It's the workers—or more specifically, the lack of workers.

The 2017 Plant Engineering Salary Survey looks at not just what plant managers make, but what they think. As they look across their plants today, plant managers say they don’t have the operational depth to take on the new technologies and new challenges of global manufacturing.

Read more: 2017 Salary Survey

The Maintenance and Reliability Coach's blog
Maintenance and reliability tips and best practices from the maintenance and reliability coaches at Allied Reliability Group.
One Voice for Manufacturing
The One Voice for Manufacturing blog reports on federal public policy issues impacting the manufacturing sector. One Voice is a joint effort by the National Tooling and Machining...
The Maintenance and Reliability Professionals Blog
The Society for Maintenance and Reliability Professionals an organization devoted...
Machine Safety
Join this ongoing discussion of machine guarding topics, including solutions assessments, regulatory compliance, gap analysis...
Research Analyst Blog
IMS Research, recently acquired by IHS Inc., is a leading independent supplier of market research and consultancy to the global electronics industry.
Marshall on Maintenance
Maintenance is not optional in manufacturing. It’s a profit center, driving productivity and uptime while reducing overall repair costs.
Lachance on CMMS
The Lachance on CMMS blog is about current maintenance topics. Blogger Paul Lachance is president and chief technology officer for Smartware Group.
Material Handling
This digital report explains how everything from conveyors and robots to automatic picking systems and digital orders have evolved to keep pace with the speed of change in the supply chain.
Electrical Safety Update
This digital report explains how plant engineers need to take greater care when it comes to electrical safety incidents on the plant floor.
IIoT: Machines, Equipment, & Asset Management
Articles in this digital report highlight technologies that enable Industrial Internet of Things, IIoT-related products and strategies.
Randy Steele
Maintenance Manager; California Oils Corp.
Matthew J. Woo, PE, RCDD, LEED AP BD+C
Associate, Electrical Engineering; Wood Harbinger
Randy Oliver
Control Systems Engineer; Robert Bosch Corp.
Data Centers: Impacts of Climate and Cooling Technology
This course focuses on climate analysis, appropriateness of cooling system selection, and combining cooling systems.
Safety First: Arc Flash 101
This course will help identify and reveal electrical hazards and identify the solutions to implementing and maintaining a safe work environment.
Critical Power: Hospital Electrical Systems
This course explains how maintaining power and communication systems through emergency power-generation systems is critical.
Design of Safe and Reliable Hydraulic Systems for Subsea Applications
This eGuide explains how the operation of hydraulic systems for subsea applications requires the user to consider additional aspects because of the unique conditions that apply to the setting
click me