Five why "nots": Using more than the "5 whys" method for root cause analysis

Using 5 Whys alone may leave engineers with an incomplete root cause picture, which is why other methods should be considered to help solve the problems and keep them from recurring.

10/24/2017


Photo by William Iven on UnsplashFirst of all, it is important to understand what 5 Whys is before exploring what it is not. It is a problem solving tool used in many facilities and is commonly associated with Lean, Six Sigma and Kaizen implementations. The technique was originally developed by Sakichi Toyoda and was used within the Toyota Motor Corporation during the evolution of its manufacturing methodologies. The method is quite simple really and involves asking "why" multiple times until the individual believes that they have reached the process cause of the problem. This sometimes (but not always) means you will stop at the fifth "why" hence the name.

While 5 Whys may be a great problem solving tool, it is not a great root cause analysis (RCA) tool for five reasons:

1. There really is no such thing as "root cause." A more correct phrase would be "root causes” because there are almost always conditions and actions that come together to manifest the failure. 5 Whys as it is most often used only addresses one branch of the causal chain either the condition or the action.

2. By only following one causal chain, you do not get the opportunity to analyze all the contributing causes and look for the lowest cost solution that eliminates or mitigates the risk to an acceptable level.

3. The results from 5 Whys are not repeatable. Different people using 5 Whys come up with different causes for the same problem. It is all based on their existing knowledge and experience.

4. Many times, 5 Whys is just used to prove what the practitioner already thought instead of looking at other possibilities. 5 Whys investigators are plagued by an inability to go beyond their current knowledge which leads to them not identifying causes that they do not already know.

5. Engineers that use 5 Whys alone do more investigations due to problem recurrence. They are sometimes celebrated for their ability to do 27 RCA investigations per month. However, when you look at the list, 18 are problems that they should have taken the time to do a true analysis the first time and they would not be focusing on them again. Using the 5 Whys method causes a tendency for investigators to stop at symptoms rather than going on to lower-level root causes, which leads to the problem recurring.

Shon Isenhour is a founding partner at Eruditio and is a part of Plant Engineering's editorial advisory board. Eruditio is a CFE Media content partner. This article originally appeared on Eruditio's blog.



Top Plant
The Top Plant program honors outstanding manufacturing facilities in North America.
Product of the Year
The Product of the Year program recognizes products newly released in the manufacturing industries.
System Integrator of the Year
Each year, a panel of Control Engineering and Plant Engineering editors and industry expert judges select the System Integrator of the Year Award winners in three categories.
October 2018
Tools vs. sensors, functional safety, compressor rental, an operational network of maintenance and safety
September 2018
2018 Engineering Leaders under 40, Women in Engineering, Six ways to reduce waste in manufacturing, and Four robot implementation challenges.
July/Aug
GAMS preview, 2018 Mid-Year Report, EAM and Safety
October 2018
2018 Product of the Year; Subsurface data methodologies; Digital twins; Well lifecycle data
August 2018
SCADA standardization, capital expenditures, data-driven drilling and execution
June 2018
Machine learning, produced water benefits, programming cavity pumps
Spring 2018
Burners for heat-treating furnaces, CHP, dryers, gas humidification, and more
October 2018
Complex upgrades for system integrators; Process control safety and compliance
September 2018
Effective process analytics; Four reasons why LTE networks are not IIoT ready

Annual Salary Survey

After two years of economic concerns, manufacturing leaders once again have homed in on the single biggest issue facing their operations:

It's the workers—or more specifically, the lack of workers.

The 2017 Plant Engineering Salary Survey looks at not just what plant managers make, but what they think. As they look across their plants today, plant managers say they don’t have the operational depth to take on the new technologies and new challenges of global manufacturing.

Read more: 2017 Salary Survey

The Maintenance and Reliability Coach's blog
Maintenance and reliability tips and best practices from the maintenance and reliability coaches at Allied Reliability Group.
One Voice for Manufacturing
The One Voice for Manufacturing blog reports on federal public policy issues impacting the manufacturing sector. One Voice is a joint effort by the National Tooling and Machining...
The Maintenance and Reliability Professionals Blog
The Society for Maintenance and Reliability Professionals an organization devoted...
Machine Safety
Join this ongoing discussion of machine guarding topics, including solutions assessments, regulatory compliance, gap analysis...
Research Analyst Blog
IMS Research, recently acquired by IHS Inc., is a leading independent supplier of market research and consultancy to the global electronics industry.
Marshall on Maintenance
Maintenance is not optional in manufacturing. It’s a profit center, driving productivity and uptime while reducing overall repair costs.
Lachance on CMMS
The Lachance on CMMS blog is about current maintenance topics. Blogger Paul Lachance is president and chief technology officer for Smartware Group.
Material Handling
This digital report explains how everything from conveyors and robots to automatic picking systems and digital orders have evolved to keep pace with the speed of change in the supply chain.
Electrical Safety Update
This digital report explains how plant engineers need to take greater care when it comes to electrical safety incidents on the plant floor.
IIoT: Machines, Equipment, & Asset Management
Articles in this digital report highlight technologies that enable Industrial Internet of Things, IIoT-related products and strategies.
Randy Steele
Maintenance Manager; California Oils Corp.
Matthew J. Woo, PE, RCDD, LEED AP BD+C
Associate, Electrical Engineering; Wood Harbinger
Randy Oliver
Control Systems Engineer; Robert Bosch Corp.
Data Centers: Impacts of Climate and Cooling Technology
This course focuses on climate analysis, appropriateness of cooling system selection, and combining cooling systems.
Safety First: Arc Flash 101
This course will help identify and reveal electrical hazards and identify the solutions to implementing and maintaining a safe work environment.
Critical Power: Hospital Electrical Systems
This course explains how maintaining power and communication systems through emergency power-generation systems is critical.
Design of Safe and Reliable Hydraulic Systems for Subsea Applications
This eGuide explains how the operation of hydraulic systems for subsea applications requires the user to consider additional aspects because of the unique conditions that apply to the setting
click me