Ethernet grows but Fieldbus is alive and well!

Ethernet is on the rise and is growing faster than Fieldbus, but overall Fieldbus usage is still greater than Ethernet.

12/09/2011


Another year of information gathering is concluding with the issue of the communications reports. Ethernet, in its various guises continues to increase its share of the market. Just looking around at the publicity and products on view at exhibitions might lead you to believe that it will swamp the market in a few years and fieldbuses will be consigned to the history books. My view is that this will not happen; the evidence for a wholesale switch to Ethernet based technologies is not there. Sure a few companies have seen good growth, I don’t doubt that but node-for-node, Ethernet will gain a few per cent share over the next 5 years.

Figure 1 shows for fieldbuses and Ethernet based protocols, the number of nodes estimated to have been installed in industrial automation networks in 2010 worldwide. At first glance it seems that fieldbuses are expected to forge ahead but in fact their share of the total market is falling.

Figure 1 shows for fieldbuses and Ethernet based protocols, the number of nodes estimated to have been installed in industrial automation networks in 2010 worldwide. At first glance it seems that fieldbuses are expected to forge ahead but in fact their sh

Figure 2 shows the forecast growth rates for 2011 to 2015 and these clearly show that Ethernet growth will slow only a little till 2014 then start to show signs of levelling off. Over the same period the fieldbus growth rate is expected to fall each year, picking up a little in 2015.

Figure 2 shows the forecast growth rates for 2011 to 2015 and these clearly show that Ethernet growth will slow only a little till 2014 then start to show signs of levelling off. Over the same period the fieldbus growth rate is expected to fall each year,

It may come as a surprise to some people that fieldbuses are still growing as fast as they are but there are several reasons why this might be.

  • Ethernet has yet to make an impact at field level; despite high growth rate being reported, the actual numbers are low when compared to nodes connected at control and supervisory level. Ethernet is frequently seen as over complex for use at field level as well as adding extra cost to the device. There are a lot of devices at field level!
  • Fieldbuses are generally much simpler to use.
  • Fieldbuses were in common use 20 years before Ethernet was considered seriously for industrial use, hence there are a lot of legacy systems and the associated knowledge base.
  • New “non-Ethernet” communication technologies and enhancements to existing ones are being added to the list all the time, e.g. I/O Link, AS-Interface, USB, FireWire etc. Some industries have their own favourites: machine vision has CameraLink and CoaXpress; building automation has BACnet and LonWorks.
  • There are many proprietary communication technologies in use today. This is particularly true in Asia, especially Japan, where the adoption of Ethernet in industry has been slow. 

Profile photo of John Morse, a senior analyst for IMS Research. Courtesy: IMS ResearchSo in conclusion; Ethernet grows but fieldbus is alive and well! All the signs are that this will continue for the foreseeable future. Ethernet and its many variants is another story, subject to its own set of rules and trends. Watch this space for the next exciting chapter!



Top Plant
The Top Plant program honors outstanding manufacturing facilities in North America.
Product of the Year
The Product of the Year program recognizes products newly released in the manufacturing industries.
System Integrator of the Year
Each year, a panel of Control Engineering and Plant Engineering editors and industry expert judges select the System Integrator of the Year Award winners in three categories.
September 2018
2018 Engineering Leaders under 40, Women in Engineering, Six ways to reduce waste in manufacturing, and Four robot implementation challenges.
July/Aug
GAMS preview, 2018 Mid-Year Report, EAM and Safety
June 2018
2018 Lubrication Guide, Motor and maintenance management, Control system migration
August 2018
SCADA standardization, capital expenditures, data-driven drilling and execution
June 2018
Machine learning, produced water benefits, programming cavity pumps
April 2018
ROVs, rigs, and the real time; wellsite valve manifolds; AI on a chip; analytics use for pipelines
Spring 2018
Burners for heat-treating furnaces, CHP, dryers, gas humidification, and more
August 2018
Choosing an automation controller, Lean manufacturing
September 2018
Effective process analytics; Four reasons why LTE networks are not IIoT ready

Annual Salary Survey

After two years of economic concerns, manufacturing leaders once again have homed in on the single biggest issue facing their operations:

It's the workers—or more specifically, the lack of workers.

The 2017 Plant Engineering Salary Survey looks at not just what plant managers make, but what they think. As they look across their plants today, plant managers say they don’t have the operational depth to take on the new technologies and new challenges of global manufacturing.

Read more: 2017 Salary Survey

The Maintenance and Reliability Coach's blog
Maintenance and reliability tips and best practices from the maintenance and reliability coaches at Allied Reliability Group.
One Voice for Manufacturing
The One Voice for Manufacturing blog reports on federal public policy issues impacting the manufacturing sector. One Voice is a joint effort by the National Tooling and Machining...
The Maintenance and Reliability Professionals Blog
The Society for Maintenance and Reliability Professionals an organization devoted...
Machine Safety
Join this ongoing discussion of machine guarding topics, including solutions assessments, regulatory compliance, gap analysis...
Research Analyst Blog
IMS Research, recently acquired by IHS Inc., is a leading independent supplier of market research and consultancy to the global electronics industry.
Marshall on Maintenance
Maintenance is not optional in manufacturing. It’s a profit center, driving productivity and uptime while reducing overall repair costs.
Lachance on CMMS
The Lachance on CMMS blog is about current maintenance topics. Blogger Paul Lachance is president and chief technology officer for Smartware Group.
Material Handling
This digital report explains how everything from conveyors and robots to automatic picking systems and digital orders have evolved to keep pace with the speed of change in the supply chain.
Electrical Safety Update
This digital report explains how plant engineers need to take greater care when it comes to electrical safety incidents on the plant floor.
IIoT: Machines, Equipment, & Asset Management
Articles in this digital report highlight technologies that enable Industrial Internet of Things, IIoT-related products and strategies.
Randy Steele
Maintenance Manager; California Oils Corp.
Matthew J. Woo, PE, RCDD, LEED AP BD+C
Associate, Electrical Engineering; Wood Harbinger
Randy Oliver
Control Systems Engineer; Robert Bosch Corp.
Data Centers: Impacts of Climate and Cooling Technology
This course focuses on climate analysis, appropriateness of cooling system selection, and combining cooling systems.
Safety First: Arc Flash 101
This course will help identify and reveal electrical hazards and identify the solutions to implementing and maintaining a safe work environment.
Critical Power: Hospital Electrical Systems
This course explains how maintaining power and communication systems through emergency power-generation systems is critical.
Design of Safe and Reliable Hydraulic Systems for Subsea Applications
This eGuide explains how the operation of hydraulic systems for subsea applications requires the user to consider additional aspects because of the unique conditions that apply to the setting
click me