Design for reliability - Part 3 of 6

What does the word performance mean to your organization? When I hear the word performance I envision a Formula Race Car at the head of the pack or an Olympic athlete crossing the finish line.

08/29/2012


What does the word performance mean to your organization? When I hear the word performance I envision a Formula Race Car at the head of the pack or an Olympic athlete crossing the finish line. Thinking specifically of the finish line and high performance, I think of all the stages it took to get to the point of crossing the finish line as number one. When I think of high performing electrical or mechanical systems at work I realize whether in a refinery, offshore platform or in 5,000 feet of water sitting on the ocean floor, there are some common themes.

While subsea reliability programs have heavily relied on models and activities developed and mastered in manufacturing and refining, subsea reliability is forced into a philosophy that creates a systems approach in its operations.

Systems reliability in subsea considers the degree of standardization in the equipment and in the tools used to repair and maintain the equipment. It allows for almost any operation to be suspended if operational limits are on the edge of being exceeded. Listed below are measures taken when limits are on the edge of being exceeded:

- Equipment such as valves and sensors have redundancy built-in
- Components are used that have a high resistance to wear and corrosion
- Condition monitoring is performed continuously on all critical pieces of equipment and on equipment that have key interfaces with critical equipment.

High performance may cost time money and resources whether you are an athlete, race car driver or a high-head pump in a refinery or an electric submersible pump in 6,000 feet of water, the payback on high performance lends to value creation.

Not all reliability high performance measures have to be gold plated to create value. Early design of the system is much like the training the athlete puts himself through. Anything that can be addressed before start up creates higher performance. These include small process improvements in the areas of:

- Spare parts identified early on for the system is commissioned
- Systems interfaces defined
- Cost on “Effort of Maintenance”
- KPIs (Key Performance Indicators)
- Failure Assessments before start-ups; with contingency measures in place
- Preparing for operational limits before they occur.

Subsea design, engineering, construction and operations integrates small process improvements along with redundancy and maintenance thought out in the design yielding performance targets that it can give back to traditional and core reliability methods.

Subsea reliability integrates improvements in design, construction, commissioning and operations. Each one of these stages considers the long term performance and how maintenance planning can be improved to deliver better system reliability. The performance targets set for subsea systems are a best practice that traditional reliability methods can leverage.



Top Plant
The Top Plant program honors outstanding manufacturing facilities in North America.
Product of the Year
The Product of the Year program recognizes products newly released in the manufacturing industries.
System Integrator of the Year
Each year, a panel of Control Engineering and Plant Engineering editors and industry expert judges select the System Integrator of the Year Award winners in three categories.
September 2018
2018 Engineering Leaders under 40, Women in Engineering, Six ways to reduce waste in manufacturing, and Four robot implementation challenges.
July/Aug
GAMS preview, 2018 Mid-Year Report, EAM and Safety
June 2018
2018 Lubrication Guide, Motor and maintenance management, Control system migration
August 2018
SCADA standardization, capital expenditures, data-driven drilling and execution
June 2018
Machine learning, produced water benefits, programming cavity pumps
April 2018
ROVs, rigs, and the real time; wellsite valve manifolds; AI on a chip; analytics use for pipelines
Spring 2018
Burners for heat-treating furnaces, CHP, dryers, gas humidification, and more
August 2018
Choosing an automation controller, Lean manufacturing
September 2018
Effective process analytics; Four reasons why LTE networks are not IIoT ready

Annual Salary Survey

After two years of economic concerns, manufacturing leaders once again have homed in on the single biggest issue facing their operations:

It's the workers—or more specifically, the lack of workers.

The 2017 Plant Engineering Salary Survey looks at not just what plant managers make, but what they think. As they look across their plants today, plant managers say they don’t have the operational depth to take on the new technologies and new challenges of global manufacturing.

Read more: 2017 Salary Survey

The Maintenance and Reliability Coach's blog
Maintenance and reliability tips and best practices from the maintenance and reliability coaches at Allied Reliability Group.
One Voice for Manufacturing
The One Voice for Manufacturing blog reports on federal public policy issues impacting the manufacturing sector. One Voice is a joint effort by the National Tooling and Machining...
The Maintenance and Reliability Professionals Blog
The Society for Maintenance and Reliability Professionals an organization devoted...
Machine Safety
Join this ongoing discussion of machine guarding topics, including solutions assessments, regulatory compliance, gap analysis...
Research Analyst Blog
IMS Research, recently acquired by IHS Inc., is a leading independent supplier of market research and consultancy to the global electronics industry.
Marshall on Maintenance
Maintenance is not optional in manufacturing. It’s a profit center, driving productivity and uptime while reducing overall repair costs.
Lachance on CMMS
The Lachance on CMMS blog is about current maintenance topics. Blogger Paul Lachance is president and chief technology officer for Smartware Group.
Material Handling
This digital report explains how everything from conveyors and robots to automatic picking systems and digital orders have evolved to keep pace with the speed of change in the supply chain.
Electrical Safety Update
This digital report explains how plant engineers need to take greater care when it comes to electrical safety incidents on the plant floor.
IIoT: Machines, Equipment, & Asset Management
Articles in this digital report highlight technologies that enable Industrial Internet of Things, IIoT-related products and strategies.
Randy Steele
Maintenance Manager; California Oils Corp.
Matthew J. Woo, PE, RCDD, LEED AP BD+C
Associate, Electrical Engineering; Wood Harbinger
Randy Oliver
Control Systems Engineer; Robert Bosch Corp.
Data Centers: Impacts of Climate and Cooling Technology
This course focuses on climate analysis, appropriateness of cooling system selection, and combining cooling systems.
Safety First: Arc Flash 101
This course will help identify and reveal electrical hazards and identify the solutions to implementing and maintaining a safe work environment.
Critical Power: Hospital Electrical Systems
This course explains how maintaining power and communication systems through emergency power-generation systems is critical.
Design of Safe and Reliable Hydraulic Systems for Subsea Applications
This eGuide explains how the operation of hydraulic systems for subsea applications requires the user to consider additional aspects because of the unique conditions that apply to the setting
click me