Dealing with the skills problem

A skilled workforce is one of the biggest problems facing plant engineers -- if not the biggest. It has been a problem for many years, and it will continue to be a problem. Consider, for example, that the U.S.

07/01/1999


A skilled workforce is one of the biggest problems facing plant engineers -- if not the biggest. It has been a problem for many years, and it will continue to be a problem.

Consider, for example, that the U.S. economy is growing faster than the population. Result: a shortage of skilled workers. Consider, too, that the nonmanufacturing sector of our economy is growing faster than the manufacturing sector. Result: A shortage of skilled workers in manufacturing. And how about this: Everyone who will enter the workforce in the next couple of decades is already alive.

Of course, the problem is qualitative as well as quantitative. The gap between skills available and skills needed is growing. While the required knowledge base is expanding, education in the basics is shrinking. Our high schools, for example, are dropping shop and mechanical arts courses like they were hot biscuits. Lack of student interest is a big factor. One study says that in 1982 almost 15% of high school graduates had taken three or more trade or industry-related courses. By 1994, that percentage dropped to less than 9%.

Our research confirms the problem. About 75% of our readers say they are becoming more involved with training, education, and skills development. And "skills of the workforce" is at the top of the list of challenges in plant engineering.

Fortunately, there are a few encouraging signs providing at least a glow, if not a light, at the end of the tunnel.

One such glow is the growing initiative to establish skill standards for manufacturing workers. It's called the Manufacturing Skill Standards Council (MSSC), and it currently involves about 175 companies, associations, unions, and educational institutions. Mission of the MSSC is to develop a nationwide system of workforce skill standards for manufacturing and related installation and repair workers. By establishing national skill standards, this group expects to enhance industrial productivity and competitiveness, guide education and training goals, and support workers' careers and opportunities.

MSSC has achieved recognition by the National Skill Standards Board. More information is available online at www.msscusa.org.

Another promising effort at skill development is the National Association of Manufacturers Virtual University. Through this internet service, NAM member companies can access online courses in basic skills. If your company belongs to NAM, check it out at www.namvu.com.





Top Plant
The Top Plant program honors outstanding manufacturing facilities in North America.
Product of the Year
The Product of the Year program recognizes products newly released in the manufacturing industries.
System Integrator of the Year
Each year, a panel of Control Engineering and Plant Engineering editors and industry expert judges select the System Integrator of the Year Award winners in three categories.
September 2018
2018 Engineering Leaders under 40, Women in Engineering, Six ways to reduce waste in manufacturing, and Four robot implementation challenges.
July/Aug
GAMS preview, 2018 Mid-Year Report, EAM and Safety
June 2018
2018 Lubrication Guide, Motor and maintenance management, Control system migration
August 2018
SCADA standardization, capital expenditures, data-driven drilling and execution
June 2018
Machine learning, produced water benefits, programming cavity pumps
April 2018
ROVs, rigs, and the real time; wellsite valve manifolds; AI on a chip; analytics use for pipelines
Spring 2018
Burners for heat-treating furnaces, CHP, dryers, gas humidification, and more
August 2018
Choosing an automation controller, Lean manufacturing
September 2018
Effective process analytics; Four reasons why LTE networks are not IIoT ready

Annual Salary Survey

After two years of economic concerns, manufacturing leaders once again have homed in on the single biggest issue facing their operations:

It's the workers—or more specifically, the lack of workers.

The 2017 Plant Engineering Salary Survey looks at not just what plant managers make, but what they think. As they look across their plants today, plant managers say they don’t have the operational depth to take on the new technologies and new challenges of global manufacturing.

Read more: 2017 Salary Survey

The Maintenance and Reliability Coach's blog
Maintenance and reliability tips and best practices from the maintenance and reliability coaches at Allied Reliability Group.
One Voice for Manufacturing
The One Voice for Manufacturing blog reports on federal public policy issues impacting the manufacturing sector. One Voice is a joint effort by the National Tooling and Machining...
The Maintenance and Reliability Professionals Blog
The Society for Maintenance and Reliability Professionals an organization devoted...
Machine Safety
Join this ongoing discussion of machine guarding topics, including solutions assessments, regulatory compliance, gap analysis...
Research Analyst Blog
IMS Research, recently acquired by IHS Inc., is a leading independent supplier of market research and consultancy to the global electronics industry.
Marshall on Maintenance
Maintenance is not optional in manufacturing. It’s a profit center, driving productivity and uptime while reducing overall repair costs.
Lachance on CMMS
The Lachance on CMMS blog is about current maintenance topics. Blogger Paul Lachance is president and chief technology officer for Smartware Group.
Material Handling
This digital report explains how everything from conveyors and robots to automatic picking systems and digital orders have evolved to keep pace with the speed of change in the supply chain.
Electrical Safety Update
This digital report explains how plant engineers need to take greater care when it comes to electrical safety incidents on the plant floor.
IIoT: Machines, Equipment, & Asset Management
Articles in this digital report highlight technologies that enable Industrial Internet of Things, IIoT-related products and strategies.
Randy Steele
Maintenance Manager; California Oils Corp.
Matthew J. Woo, PE, RCDD, LEED AP BD+C
Associate, Electrical Engineering; Wood Harbinger
Randy Oliver
Control Systems Engineer; Robert Bosch Corp.
Data Centers: Impacts of Climate and Cooling Technology
This course focuses on climate analysis, appropriateness of cooling system selection, and combining cooling systems.
Safety First: Arc Flash 101
This course will help identify and reveal electrical hazards and identify the solutions to implementing and maintaining a safe work environment.
Critical Power: Hospital Electrical Systems
This course explains how maintaining power and communication systems through emergency power-generation systems is critical.
Design of Safe and Reliable Hydraulic Systems for Subsea Applications
This eGuide explains how the operation of hydraulic systems for subsea applications requires the user to consider additional aspects because of the unique conditions that apply to the setting
click me