Adjusting to new food safety regulations in the 21st century

Unsanitary products, and in some cases outbreaks of disease, have led to a groundswell of support for new regulations, and Washington has responded.


The food industry has come under fire a bit recently, as the Food and Drug Administration has begun to crack down on farms and other food producers with respect to food safety. Unsanitary products, and in some cases outbreaks of disease, have led to a groundswell of support for new regulations, and Washington has responded.

President Barack Obama signed the Food Safety Modernization Act (FSMA) into law on Jan. 4, 2011. While the legislation is now more than five years old, every day there are still new provisions being added to the act, which was billed as the most sweeping reform of American food safety law in over 70 years. Food producers everywhere have had to adjust to a new reality in terms of compliance.

The goal of the FSMA, as Obama described it in 2011 when he signed the act, is to shift the focus. Rather than responding to contamination in food products after it happens, America now wants to prevent it. Accomplishing this will require a lot of hard work, both from FDA inspectors and the food producers on the front lines.

"The FDA plans to spend an additional $5 billion over the next five years to pay 1,000 new inspectors to oversee food production facilities and guarantee everything is up to code."

Getting On Board With The FSMA

When the FDA first proposed new legislation regarding food safety six years ago, they had good reason to do so. They'd just performed research finding that 1,442 people across 43 U.S. states had contracted salmonella poisoning from jalapeno and Serrano peppers - 300 had been hospitalized, and two were even killed. So it was clear at that point that some action was necessary. Hence the 2011 passage of the FSMA.

But the government office realized that even after passing new legislation, their work was still far from done. Michael Taylor, the FDA's deputy commissioner for foods and veterinary medicine, noted in an organizational news release that when he went to visit with farmers and other food producers, it became clear that they were having trouble meeting the new standards for compliance.

Taylor made visits in 2013 to the Pacific Northwest, New England and even overseas to Europe. During that time, he discovered that growers were becoming increasingly concerned about where food regulations were headed and how they would be affected. Not everyone was on the same page.

"The bottom line is that through these trips, our eyes were indeed opened to some realities," Taylor said. "It became clear that we'd need to make changes for the regulations to work for the food industry while still protecting public health."

This was the beginning of a long-term process. Today, years after the passage of FSMA, food producers are still working on navigating the new world of compliance.

Understanding The New Compliance Landscape

In addition to passing new legislation, Washington has also stepped up its game with regard to enforcing the rules. The FDA plans to spend an additional $5 billion over the next five years to pay 1,000 new inspectors to oversee food production facilities and guarantee everything is up to code.

There's very little room for error in the food industry now. Every year in the U.S., 3,000 people die from foodborne illnesses, and Washington knows it. There is every reason to crack down.

What Your Organization Can Do Today

If you work for a food-producing organization, what can you do to adjust to the new regulatory situation?

It always helps to educate yourself further. To that end, the Global Trade and Supply Chain Institute offers valuable information that may help your organization get up to speed and better understand the impact these regulations have on maintenance and operations—without incurring unnecessary fines and fees.

- This article originally appeared on Smartware Group blog. Smartware Group is a CFE Media content partner. Edited by Erin Dunne, production coordinator, CFE Media,

Top Plant
The Top Plant program honors outstanding manufacturing facilities in North America.
Product of the Year
The Product of the Year program recognizes products newly released in the manufacturing industries.
System Integrator of the Year
Each year, a panel of Control Engineering and Plant Engineering editors and industry expert judges select the System Integrator of the Year Award winners in three categories.
October 2018
Tools vs. sensors, functional safety, compressor rental, an operational network of maintenance and safety
September 2018
2018 Engineering Leaders under 40, Women in Engineering, Six ways to reduce waste in manufacturing, and Four robot implementation challenges.
GAMS preview, 2018 Mid-Year Report, EAM and Safety
October 2018
2018 Product of the Year; Subsurface data methodologies; Digital twins; Well lifecycle data
August 2018
SCADA standardization, capital expenditures, data-driven drilling and execution
June 2018
Machine learning, produced water benefits, programming cavity pumps
Spring 2018
Burners for heat-treating furnaces, CHP, dryers, gas humidification, and more
October 2018
Complex upgrades for system integrators; Process control safety and compliance
September 2018
Effective process analytics; Four reasons why LTE networks are not IIoT ready

Annual Salary Survey

After two years of economic concerns, manufacturing leaders once again have homed in on the single biggest issue facing their operations:

It's the workers—or more specifically, the lack of workers.

The 2017 Plant Engineering Salary Survey looks at not just what plant managers make, but what they think. As they look across their plants today, plant managers say they don’t have the operational depth to take on the new technologies and new challenges of global manufacturing.

Read more: 2017 Salary Survey

The Maintenance and Reliability Coach's blog
Maintenance and reliability tips and best practices from the maintenance and reliability coaches at Allied Reliability Group.
One Voice for Manufacturing
The One Voice for Manufacturing blog reports on federal public policy issues impacting the manufacturing sector. One Voice is a joint effort by the National Tooling and Machining...
The Maintenance and Reliability Professionals Blog
The Society for Maintenance and Reliability Professionals an organization devoted...
Machine Safety
Join this ongoing discussion of machine guarding topics, including solutions assessments, regulatory compliance, gap analysis...
Research Analyst Blog
IMS Research, recently acquired by IHS Inc., is a leading independent supplier of market research and consultancy to the global electronics industry.
Marshall on Maintenance
Maintenance is not optional in manufacturing. It’s a profit center, driving productivity and uptime while reducing overall repair costs.
Lachance on CMMS
The Lachance on CMMS blog is about current maintenance topics. Blogger Paul Lachance is president and chief technology officer for Smartware Group.
Material Handling
This digital report explains how everything from conveyors and robots to automatic picking systems and digital orders have evolved to keep pace with the speed of change in the supply chain.
Electrical Safety Update
This digital report explains how plant engineers need to take greater care when it comes to electrical safety incidents on the plant floor.
IIoT: Machines, Equipment, & Asset Management
Articles in this digital report highlight technologies that enable Industrial Internet of Things, IIoT-related products and strategies.
Randy Steele
Maintenance Manager; California Oils Corp.
Matthew J. Woo, PE, RCDD, LEED AP BD+C
Associate, Electrical Engineering; Wood Harbinger
Randy Oliver
Control Systems Engineer; Robert Bosch Corp.
Data Centers: Impacts of Climate and Cooling Technology
This course focuses on climate analysis, appropriateness of cooling system selection, and combining cooling systems.
Safety First: Arc Flash 101
This course will help identify and reveal electrical hazards and identify the solutions to implementing and maintaining a safe work environment.
Critical Power: Hospital Electrical Systems
This course explains how maintaining power and communication systems through emergency power-generation systems is critical.
Design of Safe and Reliable Hydraulic Systems for Subsea Applications
This eGuide explains how the operation of hydraulic systems for subsea applications requires the user to consider additional aspects because of the unique conditions that apply to the setting
click me