Manufacturers' focus: Sports, entertainment venues


CSE: Integration of facilities is becoming more prevalent. How is your company/product meeting this need?

Cummins Power Generation: At Target Field, the generators and transfer switches are networked with the building management system, so critical information about the status of the power sources can be monitored from the facility command center.

Uponor: As previously noted, we recognize the importance of proper controls to ensure that the systems operate as intended. We work hand in hand with the control system providers on each project to ensure that the proper sequence of operation is incorporated.

CSE: Describe some recent electrical/power system challenges you encountered when designing a new building or updating an existing building.

Cummins Power Generation: Target Field was shoe-horned into an extremely tight site on the edge of downtown Minneapolis. Locating the emergency generators was a challenge. There are two generators at opposite ends of the building, each backing up half of the facility’s load. Both are located under city streets, and one generator is located in an enclosed space that required a long run of special piping to bring in fresh air from the pedestrian concourse above, and to vent the exhaust out over a nearby freeway.

CSE: Large entertainment venues traditionally require a great deal of power during events. What resources can you offer engineers to help meet these short-duration, high-power goals?

Uponor: Yes, I think there are some folks in New Orleans who know a little something about that. One of the great benefits of hydronic-based systems is that they use a fraction of the energy required versus air-based heating systems. This can help alleviate the total load placed on the facility’s power system.

Cummins Power Generation: Given the varying power levels required at multi-purpose stadiums, it makes sense to plan on renting generators for major events. This year’s Super Bowl is a great example. CBS’s on-site equipment and Beyonce’s halftime show were both powered by rental generators; they were not connected to the stadium’s utility feed and therefore had no connection to the stadium power failure.

CSE: How have the costs and complexity of fire protection systems changed in recent years?

Notifier: Over the past decade, more fire alarm and life safety systems are using networked panels. This adds the flexibility to add new panels quickly as a facility expands. Networking also adds survivability to the life safety system because the system is spread throughout a building rather than being concentrated in a single area. If there was an event where the entire system is located, safety could be compromised. With a distributed system, the equipment outside the event area will continue to function normally. Survivability is an important feature that many building owners or facility managers are looking for today in a fire or life safety system. Another advantage of networking is ease of adding a PC-based workstation to the entire system. With a workstation the end-user has a graphical representation of the entire protected facility and can monitor the event as it unfolds, then make decisions on a response in real time. Adding networking and workstations can raise system design and equipment cost, but most buildings are willing to accept the extra expense for the benefit of improved life safety.

CSE: With regard to mass notification and emergency communication systems, what code changes do you anticipate in the near future?

Notifier: The 2010 Edition of NFPA 72, the National Fire Alarm and Signaling Code, added a new chapter, Chapter 24, dedicated to emergency communication systems. The demand for more definition of the need for and requirements of mass notification or emergency communications systems has been increasing since the mid 1990s as a result of terrorist and mass casualty incidents around the world. As more jurisdictions adopt NFPA 72-2010 and the latest version, NFPA 72-2013, more facilities will be required to have emergency communication systems that deliver emergency messages through multiple means such as voice announcements, e-mail blasts, text messages, etc., to ensure that every person is reached with the announcement whether they work in a facility, are visiting, or are in the nearby area. Having a single method of communication will no longer be adequate.

CSE: What new detection, suppression, or notification system, product, or method do you see becoming the most prevalent? Describe a recent project.

Notifier: A detection trend that is gaining traction is the use of multi-criteria detection. An example of a multi-criteria detector is a combination smoke detector with photo, infrared, temperature, and carbon monoxide sensors in a single device. Algorithms in the device use the outputs of each sensor to verify that the multiple signatures of a fire are present before sending an active fire signal to the fire alarm control panel. Multi-criteria detection can further reduce nuisance alarms, and if programmed to do so, can report out the levels of each different type of sensor. In this example the CO sensor could report actual CO levels to the panel, eliminating the need for a separate CO detector. This reduces installation and maintenance costs along with improving aesthetics for the building owner or project architect.

CSE How does your technology help engineers make their clients’ sports and entertainment structures more energy efficient?

Uponor: A radiant heating and cooling system can help dramatically reduce the energy consumption of a building through lower transport energy usage, more efficient operating modes, expanded room setpoints, lower transmission losses, and thermal inertia. Because the heat-transfer capacity of water is much higher than that of air, a radiant system that uses a pump to move water (in lieu of a fan to move air) can achieve the same heat transfer using significantly less energy.

CSE: What HVAC issue comes to the forefront most when you’re supporting engineers in such facilities? How do you help overcome these issues/answer their questions?

Uponor: When an engineer is considering radiant cooling, one of the common issues that seems to come up is surface condensation. Condensation on the floor is both a safety and a maintenance concern. This would occur if the surface temperature ever dropped below the dewpoint. This is of particular concern in high-occupancy areas such as sporting or entertainment venues, where the latent load could be significant. In order to address this, however, one needs to look at the HVAC system as a whole. If the system is properly designed to maintain temperature and relative humidity levels conducive to human health and comfort, then it would be unlikely that you would have indoor dew points close to the 66 to 68 F minimum floor surface temperature recommended by ASHRAE Standard 55

<< First < Previous Page 1 Page 2 Next > Last >>

The Top Plant program honors outstanding manufacturing facilities in North America. View the 2015 Top Plant.
The Product of the Year program recognizes products newly released in the manufacturing industries.
Each year, a panel of Control Engineering and Plant Engineering editors and industry expert judges select the System Integrator of the Year Award winners in three categories.
Pipe fabrication and IIoT; 2017 Product of the Year finalists
The future of electrical safety; Four keys to RPM success; Picking the right weld fume option
A new approach to the Skills Gap; Community colleges may hold the key for manufacturing; 2017 Engineering Leaders Under 40
Control room technology innovation; Practical approaches to corrosion protection; Pipeline regulator revises quality programs
The cloud, mobility, and remote operations; SCADA and contextual mobility; Custom UPS empowering a secure pipeline
Infrastructure for natural gas expansion; Artificial lift methods; Disruptive technology and fugitive gas emissions
Power system design for high-performance buildings; mitigating arc flash hazards
VFDs improving motion control applications; Powering automation and IIoT wirelessly; Connecting the dots
Natural gas engines; New applications for fuel cells; Large engines become more efficient; Extending boiler life

Annual Salary Survey

Before the calendar turned, 2016 already had the makings of a pivotal year for manufacturing, and for the world.

There were the big events for the year, including the United States as Partner Country at Hannover Messe in April and the 2016 International Manufacturing Technology Show in Chicago in September. There's also the matter of the U.S. presidential elections in November, which promise to shape policy in manufacturing for years to come.

But the year started with global economic turmoil, as a slowdown in Chinese manufacturing triggered a worldwide stock hiccup that sent values plummeting. The continued plunge in world oil prices has resulted in a slowdown in exploration and, by extension, the manufacture of exploration equipment.

Read more: 2015 Salary Survey

Maintenance and reliability tips and best practices from the maintenance and reliability coaches at Allied Reliability Group.
The One Voice for Manufacturing blog reports on federal public policy issues impacting the manufacturing sector. One Voice is a joint effort by the National Tooling and Machining...
The Society for Maintenance and Reliability Professionals an organization devoted...
Join this ongoing discussion of machine guarding topics, including solutions assessments, regulatory compliance, gap analysis...
IMS Research, recently acquired by IHS Inc., is a leading independent supplier of market research and consultancy to the global electronics industry.
Maintenance is not optional in manufacturing. It’s a profit center, driving productivity and uptime while reducing overall repair costs.
The Lachance on CMMS blog is about current maintenance topics. Blogger Paul Lachance is president and chief technology officer for Smartware Group.
The maintenance journey has been a long, slow trek for most manufacturers and has gone from preventive maintenance to predictive maintenance.
This digital report explains how plant engineers and subject matter experts (SME) need support for time series data and its many challenges.
This digital report will explore several aspects of how IIoT will transform manufacturing in the coming years.
Maintenance Manager; California Oils Corp.
Associate, Electrical Engineering; Wood Harbinger
Control Systems Engineer; Robert Bosch Corp.
This course focuses on climate analysis, appropriateness of cooling system selection, and combining cooling systems.
This course will help identify and reveal electrical hazards and identify the solutions to implementing and maintaining a safe work environment.
This course explains how maintaining power and communication systems through emergency power-generation systems is critical.
click me