Machine Safety: Benefits of safety assessments, risk assessments

The need to evaluate hazards and apply corrective actions to reduce those hazards began years ago. Over the past 12-plus years this process has been refined, documented in standards and regulations, and it’s now a requirement. A general term defined for this process is “risk assessment.” Below, learn who a risk assessment is for and some best practices for a risk assessment.

01/09/2015


In the functional safety life cycle, 1) Perform risk assessment 2) Examine functional requirements 3) Design and verify mitigation 4) Install and validate 5) Manage, change, and improve. Courtesy: Control Engineering Machine Safety Blog, JB Titus & Associates

 

The need to evaluate hazards and apply corrective actions to reduce machine safety hazards began years ago. Over the past 12-plus years this process has been refined, documented in standards and regulations, and it's now a requirement. A general term defined for this process is "risk assessment." What is a risk assessment and who benefits?

A risk assessment as defined by ISO 12100: 2010 (Safety of Machinery — General requirements for design — Risk assessment and risk reduction) is required for designers:

1 Scope

This International Standard specifies basic terminology, principles and a methodology for achieving safety in the design of machinery. It specifies principles of risk assessment and risk reduction to help designers in achieving this objective. These principles are based on knowledge and experience of the design, use, incidents, accidents and risks associated with machinery. Procedures are described for identifying hazards and estimating and evaluating risks during relevant phases of the machine life cycle, and for the elimination of hazards or the provision of sufficient risk reduction.

Therefore, in my opinion, ISO 12100 lays out a process for conducting and recording a risk assessment and the associated risk reduction measures. These measures are intended to reduce the risk level of each identified hazard to an acceptable level. Furthermore, other machine safety application standards also have normative (required) references to this standard. As such, ISO 12100 becomes a required standard across industry and in fact it has become the accepted global risk assessment standard.

The "designers" referenced in ISO 12100 are described by industry experts as persons designing new machines and retrofits or upgrades to existing machines. The term designers would then apply, as a minimum, to original equipment manufacturers (OEMs), engineering firms, systems integrators, or end users. In my opinion, designers implement the requirements for risk assessments according to ISO 12100.

Risk assessment best practices

But, who are risk assessments for?

With all of this process language for properly conducting risk assessments documented and published in machine safety standards (ISO 12100) — can anyone point to similar normative language in a machine safety standard stating who risk assessments are for? I have discovered that risk assessments actually are beneficial in a broader sense to a company's business. As such, here are a few best practices:

  • Keep every risk assessment on file.
  • Update risk assessments to keep them current.
  • Provide a copy to the company legal department.
  • Send a copy to the company chief executive officer.
  • Provide a copy to the company's insurance department/carrier.

Furthermore, risk assessments are known to impact company image, employee morale, stock holders, financial balance sheets, return on investments (ROI) and payments to workers compensation.

Therefore, who are the risk assessments for? In my opinion — the entire business!

What machine standards do you find particularly useful and why? What tipse can you share about doing risk assessments? Comment and see related articles linked below.

- J.B. Titus, certified functional safety expert (CFSE), writes the Control Engineering Machine Safety Blog. Edited by Mark T. Hoske, content manager, Control Engineering, mhoske@cfemedia.com.

Online extra

Other online risk assessment articles are linked below:

Machine Safety: Design a safer machine with risk assessments

Machine Safety: Consequences of not performing risk assessments!

Machine Safety: Does a risk assessment need to be updated for a minor machine modification?

Contact: http://www.jbtitus.com for "Solutions for Machine Safety."



Top Plant
The Top Plant program honors outstanding manufacturing facilities in North America.
Product of the Year
The Product of the Year program recognizes products newly released in the manufacturing industries.
System Integrator of the Year
Each year, a panel of Control Engineering and Plant Engineering editors and industry expert judges select the System Integrator of the Year Award winners in three categories.
September 2018
2018 Engineering Leaders under 40, Women in Engineering, Six ways to reduce waste in manufacturing, and Four robot implementation challenges.
July/Aug
GAMS preview, 2018 Mid-Year Report, EAM and Safety
June 2018
2018 Lubrication Guide, Motor and maintenance management, Control system migration
August 2018
SCADA standardization, capital expenditures, data-driven drilling and execution
June 2018
Machine learning, produced water benefits, programming cavity pumps
April 2018
ROVs, rigs, and the real time; wellsite valve manifolds; AI on a chip; analytics use for pipelines
Spring 2018
Burners for heat-treating furnaces, CHP, dryers, gas humidification, and more
August 2018
Choosing an automation controller, Lean manufacturing
September 2018
Effective process analytics; Four reasons why LTE networks are not IIoT ready

Annual Salary Survey

After two years of economic concerns, manufacturing leaders once again have homed in on the single biggest issue facing their operations:

It's the workers—or more specifically, the lack of workers.

The 2017 Plant Engineering Salary Survey looks at not just what plant managers make, but what they think. As they look across their plants today, plant managers say they don’t have the operational depth to take on the new technologies and new challenges of global manufacturing.

Read more: 2017 Salary Survey

The Maintenance and Reliability Coach's blog
Maintenance and reliability tips and best practices from the maintenance and reliability coaches at Allied Reliability Group.
One Voice for Manufacturing
The One Voice for Manufacturing blog reports on federal public policy issues impacting the manufacturing sector. One Voice is a joint effort by the National Tooling and Machining...
The Maintenance and Reliability Professionals Blog
The Society for Maintenance and Reliability Professionals an organization devoted...
Machine Safety
Join this ongoing discussion of machine guarding topics, including solutions assessments, regulatory compliance, gap analysis...
Research Analyst Blog
IMS Research, recently acquired by IHS Inc., is a leading independent supplier of market research and consultancy to the global electronics industry.
Marshall on Maintenance
Maintenance is not optional in manufacturing. It’s a profit center, driving productivity and uptime while reducing overall repair costs.
Lachance on CMMS
The Lachance on CMMS blog is about current maintenance topics. Blogger Paul Lachance is president and chief technology officer for Smartware Group.
Material Handling
This digital report explains how everything from conveyors and robots to automatic picking systems and digital orders have evolved to keep pace with the speed of change in the supply chain.
Electrical Safety Update
This digital report explains how plant engineers need to take greater care when it comes to electrical safety incidents on the plant floor.
IIoT: Machines, Equipment, & Asset Management
Articles in this digital report highlight technologies that enable Industrial Internet of Things, IIoT-related products and strategies.
Randy Steele
Maintenance Manager; California Oils Corp.
Matthew J. Woo, PE, RCDD, LEED AP BD+C
Associate, Electrical Engineering; Wood Harbinger
Randy Oliver
Control Systems Engineer; Robert Bosch Corp.
Data Centers: Impacts of Climate and Cooling Technology
This course focuses on climate analysis, appropriateness of cooling system selection, and combining cooling systems.
Safety First: Arc Flash 101
This course will help identify and reveal electrical hazards and identify the solutions to implementing and maintaining a safe work environment.
Critical Power: Hospital Electrical Systems
This course explains how maintaining power and communication systems through emergency power-generation systems is critical.
Design of Safe and Reliable Hydraulic Systems for Subsea Applications
This eGuide explains how the operation of hydraulic systems for subsea applications requires the user to consider additional aspects because of the unique conditions that apply to the setting
click me