Using lasers to create flat floors

Many companies opt to maximize space utilization in their storage areas by installing floor-to-ceiling racking systems separated by very narrow aisles.

09/01/1999


Many companies opt to maximize space utilization in their storage areas by installing floor-to-ceiling racking systems separated by very narrow aisles. In order to move product to and from this racking arrangement, very narrow aisle (VNA) reach trucks are used.

Some VNA reach trucks travel with the load fully elevated over 40 ft with a side-to-side clearance between the truck mast and racking of only 4 in. A difference of 1/8 in. in floor elevation between a VNA reach truck's two front wheels set 47-in. apart translates to a static lean of 1 1/4 in. at a height of about 40 ft.

Mast sway when the truck is traveling could triple the static lean and lead to collisions between the mast and racking. In addition to rack damage, floors with poor flatness characteristics can also cause premature failure of truck welds and disrupt wire guidance performance.

A plant engineer faced with collisions between vehicles and racking has no alternative but to reduce the speed of the trucks, which decreases pallet throughput and productivity.

Traditional approaches

Until recently, the solution to improving floor flatness characteristics was either manual grinding or installing a bonded concrete overlay system.

Manual grinding is performed with a rotary machine readily available from construction rental supply firms. This approach utilizes a rotary grinder to remove high spots, as determined by a straightedge placed on the floor. Manual grinding provides an economical solution to floor aisle spot imperfections.

However, with whole aisle or wheel path grinding, the manual method is extremely slow, messy, costly and often leaves the floor concave rather than at a flat plane.

Bonded concrete overlays are the second alternative. The existing floor is cleaned and roughened. A bonding agent is applied between the base concrete and the 3/4-1-in. thick concrete topping, in order to stick the new topping to the old floor. Concrete overlays enhance the structural capacity of a floor slab because the bonded topping becomes composite with the concrete floor to increase load carrying capacity.

Bonded concrete toppings can be placed in narrow strip fashion so that floor flatness tolerances are enhanced far above the original aisle tolerances. Overlays have the added advantage of restoring aisle surfaces to new condition.

Bonded concrete overlay systems run the risk of debonding if surface preparation is not properly performed. Also, any cracks in the base slab eventually reflect into the topping slab.

Since concrete overlays are only placed in aisles, the raised elevation can make utilization of the bottom pallet station problematic. Overlays also require preparation and cure time lasting several days.

Latest approach

Laser grinding is the newest approach to enhance concrete floor flatness. This process improves floor aisle tolerances by grinding just the wheel paths of VNA reach trucks, or the full width of the aisle if the client chooses. A rotating laser positioned at the end of the work area controls the depth of cut. A pair of laser receivers mounted on each grinding head is interfaced with a control box that corrects the depth of cut.

After an aisle is surveyed, both wheel paths are ground to a common profile across the aisle, which eliminates the side-to-side sway of the loaded vehicle as it travels elevated down the path. In order to minimize the amount of concrete removed, the longitudinal plane goes up and down the length of the aisle in lieu of carrying out grinding from the lowest point and making the floor flat to it.

Wheel path grinding could create clearance problems for the truck when deep cuts are required to correct transverse tolerance problems. Floor aisles that have been ground can present problems to an operation that subsequently changes racking location and orientation.

The laser grinding process is clean and dust free. Product can be left in the racks during the grinding operation. The client has the ability to retrieve product either in front or behind the grinding operation as it takes place. Once an aisle has been ground, it can be immediately returned to service.

Improved floor flatness allows operators to safely run the VNA reach trucks at maximum speed. The increase in pallet per hour throughput and reduced truck maintenance costs easily provide a paybackfor the operation in just a few months.

-- Edited by Ron Holzhauer, Managing Editor, 630-320-7139, r.holzhauer@cahners.com

Key concepts

Very narrow aisle reach trucks require flat floors.

Traditional methods for improving floor flatness are manual grinding and a bonded concrete overlay.

Laser grinding offers several advantages over the more traditional approaches.





No comments
The Top Plant program honors outstanding manufacturing facilities in North America. View the 2015 Top Plant.
The Product of the Year program recognizes products newly released in the manufacturing industries.
The Engineering Leaders Under 40 program identifies and gives recognition to young engineers who...
2016 Product of the Year; Diagnose bearing failures; Asset performance management; Testing dust collector performance measures
Safety for 18 years, warehouse maintenance tips, Ethernet and the IIoT, GAMS 2016 recap
2016 Engineering Leaders Under 40; Future vision: Where is manufacturing headed?; Electrical distribution, redefined
SCADA at the junction, Managing risk through maintenance, Moving at the speed of data
Safety at every angle, Big Data's impact on operations, bridging the skills gap
The digital oilfield: Utilizing Big Data can yield big savings; Virtualization a real solution; Tracking SIS performance
Applying network redundancy; Overcoming loop tuning challenges; PID control and networks
Driving motor efficiency; Preventing arc flash in mission critical facilities; Integrating alternative power and existing electrical systems
Package boilers; Natural gas infrared heating; Thermal treasure; Standby generation; Natural gas supports green efforts

Annual Salary Survey

Before the calendar turned, 2016 already had the makings of a pivotal year for manufacturing, and for the world.

There were the big events for the year, including the United States as Partner Country at Hannover Messe in April and the 2016 International Manufacturing Technology Show in Chicago in September. There's also the matter of the U.S. presidential elections in November, which promise to shape policy in manufacturing for years to come.

But the year started with global economic turmoil, as a slowdown in Chinese manufacturing triggered a worldwide stock hiccup that sent values plummeting. The continued plunge in world oil prices has resulted in a slowdown in exploration and, by extension, the manufacture of exploration equipment.

Read more: 2015 Salary Survey

Maintenance and reliability tips and best practices from the maintenance and reliability coaches at Allied Reliability Group.
The One Voice for Manufacturing blog reports on federal public policy issues impacting the manufacturing sector. One Voice is a joint effort by the National Tooling and Machining...
The Society for Maintenance and Reliability Professionals an organization devoted...
Join this ongoing discussion of machine guarding topics, including solutions assessments, regulatory compliance, gap analysis...
IMS Research, recently acquired by IHS Inc., is a leading independent supplier of market research and consultancy to the global electronics industry.
Maintenance is not optional in manufacturing. It’s a profit center, driving productivity and uptime while reducing overall repair costs.
The Lachance on CMMS blog is about current maintenance topics. Blogger Paul Lachance is president and chief technology officer for Smartware Group.
This article collection contains several articles on the vital role of plant safety and offers advice on best practices.
This article collection contains several articles on the Industrial Internet of Things (IIoT) and how it is transforming manufacturing.
This article collection contains several articles on strategic maintenance and understanding all the parts of your plant.
click me