Reader response

Band control The solution submitted in the December issue titled "Band Control" is a good idea. US Patent # 4,746,011 was issued to me on May 24, 1988, for this safety problem solution. I'd like to point out that the idea that was submitted had been tried during development, but we found the results were still too chancy and it was difficult to use.

02/15/2003


Band control

The solution submitted in the December issue titled "Band Control" is a good idea. US Patent # 4,746,011 was issued to me on May 24, 1988, for this safety problem solution. I'd like to point out that the idea that was submitted had been tried during development, but we found the results were still too chancy and it was difficult to use. I'd hate to see someone get hurt using something they think will protect them.

The patent covered a variety of designs, but what we finally settled on was a piece of moderate weight canvas drop cloth large enough to drape over all four edges of the package. We sewed a piece of light chain into a hem in the perimeter of the cloth. The chain made it easy to throw over a load (like casting a bait net) but still light and not too stiff to handle. The chain kept the cloth from slipping and was very effective at stopping the strap dead. It was considered a safety device and as such was kept stowed always conveniently close to where packages were opened. — Sam McNair

Data mining

I was very surprised at your December article about data mining as it applies to maintenance. The cost of implementing such a program would far outweigh the cost saving. Such a system is only as good as the data collected and then only as good as the person collecting the data. It's not a good idea to have valuable maintenance men going around collecting all day. It's hard enough making sure the work orders are being done and not being copied from last week's PM's. Besides, any good maintenance manager knows cost, when, and where his downtime is coming from. — Joseph J. Veverka

Pump reliability references

PLANT ENGINEERING neglected to include the following references with the December article on "Improving Pump Reliability."

1. Bloch, H.P. and Geitner, F.K., An Introduction to Machinery Reliability Assessment , 2nd ed., Gulf Publishing Co., Houston, TX (1994).

2. R. Barry Erickson, Eugene P. Sabini, Anthony Stavale, ITT Industries%%MDASSML%%Goulds Pumps, Hydraulic Selection to Minimize the Unscheduled Maintenance Portion of Life Cycle Cost , 1998

3. Dr. Lev Nelik, ITT Industries %%MDASSML%% Goulds Pumps, Bearing Life Extension and Reliability Features of Modern ANSI Pumps , The 2nd International Conference on Improving Reliability in Petroleum Refineries and Chemical and Natural Gas Plants, 1993.





No comments
The Top Plant program honors outstanding manufacturing facilities in North America. View the 2015 Top Plant.
The Product of the Year program recognizes products newly released in the manufacturing industries.
The Engineering Leaders Under 40 program identifies and gives recognition to young engineers who...
2016 Product of the Year; Diagnose bearing failures; Asset performance management; Testing dust collector performance measures
Safety for 18 years, warehouse maintenance tips, Ethernet and the IIoT, GAMS 2016 recap
2016 Engineering Leaders Under 40; Future vision: Where is manufacturing headed?; Electrical distribution, redefined
SCADA at the junction, Managing risk through maintenance, Moving at the speed of data
Safety at every angle, Big Data's impact on operations, bridging the skills gap
The digital oilfield: Utilizing Big Data can yield big savings; Virtualization a real solution; Tracking SIS performance
Applying network redundancy; Overcoming loop tuning challenges; PID control and networks
Driving motor efficiency; Preventing arc flash in mission critical facilities; Integrating alternative power and existing electrical systems
Package boilers; Natural gas infrared heating; Thermal treasure; Standby generation; Natural gas supports green efforts

Annual Salary Survey

Before the calendar turned, 2016 already had the makings of a pivotal year for manufacturing, and for the world.

There were the big events for the year, including the United States as Partner Country at Hannover Messe in April and the 2016 International Manufacturing Technology Show in Chicago in September. There's also the matter of the U.S. presidential elections in November, which promise to shape policy in manufacturing for years to come.

But the year started with global economic turmoil, as a slowdown in Chinese manufacturing triggered a worldwide stock hiccup that sent values plummeting. The continued plunge in world oil prices has resulted in a slowdown in exploration and, by extension, the manufacture of exploration equipment.

Read more: 2015 Salary Survey

Maintenance and reliability tips and best practices from the maintenance and reliability coaches at Allied Reliability Group.
The One Voice for Manufacturing blog reports on federal public policy issues impacting the manufacturing sector. One Voice is a joint effort by the National Tooling and Machining...
The Society for Maintenance and Reliability Professionals an organization devoted...
Join this ongoing discussion of machine guarding topics, including solutions assessments, regulatory compliance, gap analysis...
IMS Research, recently acquired by IHS Inc., is a leading independent supplier of market research and consultancy to the global electronics industry.
Maintenance is not optional in manufacturing. It’s a profit center, driving productivity and uptime while reducing overall repair costs.
The Lachance on CMMS blog is about current maintenance topics. Blogger Paul Lachance is president and chief technology officer for Smartware Group.
This article collection contains several articles on the vital role of plant safety and offers advice on best practices.
This article collection contains several articles on the Industrial Internet of Things (IIoT) and how it is transforming manufacturing.
This article collection contains several articles on strategic maintenance and understanding all the parts of your plant.
click me