'No longer in a freefall'

MAPI manufacturing index shows signs of recovery for first time in two years


The road to recovery in the manufacturing sector will likely be slow, arduous, and painstaking, but there is some evidence that the worst has passed, according to the quarterly Manufacturers Alliance/MAPI Survey on the Business Outlook for June 2009, a leading indicator for the industrial sector. The June 2009 composite index rose to 24 from an historic low of 21 reported in the March 2009 report.
At 24, the index indicates that overall manufacturing activity is expected to contract over the next three to six months. While the index is at its second lowest level since the survey originated in March 1972, it marks the first time it has shown improvement since June 2007. The survey was conducted on a semi-annual basis from 1972 to 1991 before being conducted on a quarterly basis in 1991. It should be noted, however, that the index measures the direction of change rather than the absolute strength of activity in manufacturing.
The June 2009 index of 24 marks the fourth consecutive quarterly reading below 50, the demarcation point between growth and contraction, and pales in comparison to one year ago when the June 2008 index registered at the 50 mid-point.
"The small rise in the composite index and the improvement in a few of the individual indexes indicate that the manufacturing sector is no longer in a freefall," said Donald A. Norman, Ph.D., MAPI Economist and survey coordinator, "even as the forward looking indexes point to lower activity over the next three to six months." Norman noted that most of the individual indexes are based on year-over-year comparisons. A year ago manufacturing activity was down somewhat, but still at a relatively high level. Given the sharp fall in activity over the past nine months, it is hardly surprising that year-over-year comparisons have resulted in sharp declines in the indexes.
While a variety of individual indexes are included in the survey, the business outlook index is a weighted sum of the shipments, backlogs, inventories, and profit margin indexes.
Seven of the 12 individual indexes measured in the survey fell to all-time lows, but only slightly and none by more than five points. The declines were offset somewhat by improvement in other areas. In the March 2009 survey, 11 of the 12 indexes reached all-time lows.
The brightest news may have come in the inventory index, based on a comparison of inventory levels in the second quarter of 2009 with those of one year ago. It dropped to 15% in June from 37% in March, indicating that manufacturers are making substantial progress in paring an inventory overhang.
The non-U.S. prospective shipments index, which measures expectations for shipments abroad by foreign affiliates of U.S. firms in the third quarter of 2009 compared to the same quarter of 2008, rose to 15% from 8%. The export orders index, which measures how second quarter 2009 exports compare with those of second quarter 2008, increased to 11% in June from 8% in the March survey.
The quarterly orders index, which compared new orders for the second quarter of 2009 with the same quarter one year ago, edged up to 6% from 4% in the previous survey. The U.S. investment index, which queried executives on their expectations regarding capital investment in 2009 compared to 2008, held steady at 14% in June from the March report.

No comments
The Top Plant program honors outstanding manufacturing facilities in North America. View the 2015 Top Plant.
The Product of the Year program recognizes products newly released in the manufacturing industries.
The Engineering Leaders Under 40 program identifies and gives recognition to young engineers who...
Safety for 18 years, warehouse maintenance tips, Ethernet and the IIoT, GAMS 2016 recap
2016 Engineering Leaders Under 40; Future vision: Where is manufacturing headed?; Electrical distribution, redefined
Strategic outsourcing delivers efficiency; Sleeve bearing clearance; Causes of water hammer; Improve air quality; Maintenance safety; GAMS preview
SCADA at the junction, Managing risk through maintenance, Moving at the speed of data
Safety at every angle, Big Data's impact on operations, bridging the skills gap
The digital oilfield: Utilizing Big Data can yield big savings; Virtualization a real solution; Tracking SIS performance
Applying network redundancy; Overcoming loop tuning challenges; PID control and networks
Driving motor efficiency; Preventing arc flash in mission critical facilities; Integrating alternative power and existing electrical systems
Package boilers; Natural gas infrared heating; Thermal treasure; Standby generation; Natural gas supports green efforts

Annual Salary Survey

Before the calendar turned, 2016 already had the makings of a pivotal year for manufacturing, and for the world.

There were the big events for the year, including the United States as Partner Country at Hannover Messe in April and the 2016 International Manufacturing Technology Show in Chicago in September. There's also the matter of the U.S. presidential elections in November, which promise to shape policy in manufacturing for years to come.

But the year started with global economic turmoil, as a slowdown in Chinese manufacturing triggered a worldwide stock hiccup that sent values plummeting. The continued plunge in world oil prices has resulted in a slowdown in exploration and, by extension, the manufacture of exploration equipment.

Read more: 2015 Salary Survey

Maintenance and reliability tips and best practices from the maintenance and reliability coaches at Allied Reliability Group.
The One Voice for Manufacturing blog reports on federal public policy issues impacting the manufacturing sector. One Voice is a joint effort by the National Tooling and Machining...
The Society for Maintenance and Reliability Professionals an organization devoted...
Join this ongoing discussion of machine guarding topics, including solutions assessments, regulatory compliance, gap analysis...
IMS Research, recently acquired by IHS Inc., is a leading independent supplier of market research and consultancy to the global electronics industry.
Maintenance is not optional in manufacturing. It’s a profit center, driving productivity and uptime while reducing overall repair costs.
The Lachance on CMMS blog is about current maintenance topics. Blogger Paul Lachance is president and chief technology officer for Smartware Group.
This article collection contains several articles on the vital role of plant safety and offers advice on best practices.
This article collection contains several articles on the Industrial Internet of Things (IIoT) and how it is transforming manufacturing.
This article collection contains several articles on strategic maintenance and understanding all the parts of your plant.
click me