Machine Safety: System degradation and incidence of injury

Are older hardwired safety systems less safe than newer integrated safety systems? (See table.) Since 2002 when integrated safety automation was introduced for machine safety, a growing awareness has emerged questioning the effectiveness over time of a hardwired / hardware safety system versus an integrated safety system. What is the ultimate effectiveness of a safety-related function comparing the date of commissioning to a date several years later given the two approaches?

02/17/2012


JB Titus, CFSESince 2002 when integrated safety automation was introduced for machine safety, a growing awareness has emerged questioning the effectiveness over time of a hardwired / hardware safety system versus an integrated safety system. What is the ultimate effectiveness of a safety-related function comparing the date of commissioning to a date several years later given the two approaches?

   I’ve been asked this question many times over the past 10 years causing me to do some research. So far I haven’t been successful in finding comparative data for example on the incidence of injuries for:

1)   Newly commissioned hardwired / hardware safety systems performing safety-related functions.

2)   Versus, (for example) 10-year-old hardwired / hardware safety systems performing safety-related functions.

   Nor have I found any convincing data on the incidence of injuries comparing hardwired versus integrated (software / firmware) safety systems. What I have found via research, multiple interviews, and personal experience is that the answer usually boils down to the eventual safety culture discussion. I believe the ultimate answer lies in the “Mean Time To Fail Dangerous” (MTTFD) comparison of the two approaches. Most everyone agrees that both approaches are arguably equal at date of commissioning (new) in their effectiveness and reliability to perform the intended safety-related function. However, the safety culture issue could be the determinate factor to differentiate their comparative effectiveness and reliability over time. This comparison, in my opinion, is represented in the table below.

 

Comparing older versus newer machine safety systems

Hardwired / Hardware Safety Systems

 

 

 

Integrated Safety Systems

 

Inflexible – no software

 

Flexibility

 

Flexible via software

 

Few to none

 

Diagnostics

 

System provided at HMI

 

Significant un-planned downtime with high trouble shoot time

 

Downtime

 

Minimal un-planned downtime with low trouble shoot time

 

Broken / loose cables

 

Intermittent breakdown

 

60 to 80 percent fewer cables

 

Insecure access

 

System integrity

 

Levels of access security

 

Finite

 

MTTFD

 

10-8

 

Increases over time

 

Maintenance

 

Constant over time

 

 

This discussion is intended to create some cognitive thinking concerning the question of effectiveness and reliability of the intended safety-related function given the two approaches and the lack of supporting incidence data. Additionally, we have abundant supporting testimonials today that report reduced costs and increased productivity with integrated versus hardwired safety systems. This of course depends on the size, complexity, and number of machines on the plant floor.

   As a plant manager, you’re the one responsible individual who can evaluate your safety culture and choose the best alternative approach for machine safety for your business.

   Are older hardwired safety systems less safe than newer integrated safety systems? Your comments or suggestion are always welcome so please let us know your thoughts. Submit your ideas, experiences, and challenges on this subject in the comments section below. Click on the following text if you don't see a comments box, then scroll down: Machine Safety: System degradation and incidence of injury.

Safety matters logo.   Related articles:

Updating Minds About Machine Safety

Machine Safety Culture – compliance versus cooperation driven

Machine Safety – the myths of safety cultures.

   Contact: www.jbtitus.com for “Solutions for Machine Safety”.



No comments
The Top Plant program honors outstanding manufacturing facilities in North America. View the 2015 Top Plant.
The Product of the Year program recognizes products newly released in the manufacturing industries.
The Engineering Leaders Under 40 program identifies and gives recognition to young engineers who...
Hannover Messe 2016: Taking hold of the future - Partner Country status spotlights U.S. manufacturing; Honoring manufacturing excellence: The 2015 Product of the Year Winners
Inside IIoT: How technology, strategy can improve your operation; Dry media or web scrubber?; Six steps to design a PM program
World-class manufacturing: A recipe for success: Finding the right mix for a salad dressing line; 2015 Salary Survey: Manufacturing slump dims enthusiasm
Getting to the bottom of subsea repairs: Older pipelines need more attention, and operators need a repair strategy; OTC preview; Offshore production difficult - and crucial
Digital oilfields: Integrated HMI/SCADA systems enable smarter data acquisition; Real-world impact of simulation; Electric actuator technology prospers in production fields
Special report: U.S. natural gas; LNG transport technologies evolve to meet market demand; Understanding new methane regulations; Predictive maintenance for gas pipeline compressors
Warehouse winter comfort: The HTHV solution; Cooling with natural gas; Plastics industry booming
Managing automation upgrades, retrofits; Making technical, business sense; Ensuring network cyber security
Designing generator systems; Using online commissioning tools; Selective coordination best practices

Annual Salary Survey

Before the calendar turned, 2016 already had the makings of a pivotal year for manufacturing, and for the world.

There were the big events for the year, including the United States as Partner Country at Hannover Messe in April and the 2016 International Manufacturing Technology Show in Chicago in September. There's also the matter of the U.S. presidential elections in November, which promise to shape policy in manufacturing for years to come.

But the year started with global economic turmoil, as a slowdown in Chinese manufacturing triggered a worldwide stock hiccup that sent values plummeting. The continued plunge in world oil prices has resulted in a slowdown in exploration and, by extension, the manufacture of exploration equipment.

Read more: 2015 Salary Survey

Maintenance and reliability tips and best practices from the maintenance and reliability coaches at Allied Reliability Group.
The One Voice for Manufacturing blog reports on federal public policy issues impacting the manufacturing sector. One Voice is a joint effort by the National Tooling and Machining...
The Society for Maintenance and Reliability Professionals an organization devoted...
Join this ongoing discussion of machine guarding topics, including solutions assessments, regulatory compliance, gap analysis...
IMS Research, recently acquired by IHS Inc., is a leading independent supplier of market research and consultancy to the global electronics industry.
Maintenance is not optional in manufacturing. It’s a profit center, driving productivity and uptime while reducing overall repair costs.
The Lachance on CMMS blog is about current maintenance topics. Blogger Paul Lachance is president and chief technology officer for Smartware Group.
This article collection contains several articles on the vital role that compressed air plays in manufacturing plants.
This article collection contains several articles on the Industrial Internet of Things (IIoT) and how it is transforming manufacturing.
click me