Industry trend talk: Using steam tracing for process

Heat tracing can be used to heat a variety of products. Understanding the basics of sizing and installing external line tracing will help you apply it effectively.


Often, the temperature of process liquids being transferred through pipelines must be maintained to meet process requirements, prevent thickening and solidification, or simply to protect against freeze-up. This is achieved with jacketed pipes or by attaching one or more tracing lines (carrying a heating medium such as steam or hot water) to the product’s pipeline. In these applications, steam usage may be relatively small, but the tracing system usually is a major component of the steam installation and the source of many problems.

While no single article can address all of the contingencies affecting a steam tracing system, the following guidelines provide an overview of items to consider. Only external tracing is addressed because this is the area most likely to cause difficulties when no existing experience is available. External tracing is simple, and, therefore, inexpensive to install and fulfills the most processes’ needs.

External tracer lines

One or more heat-carrying lines, sized from 0.375 to 1 in. normal bore, are attached to the main product pipe. Heat transfers to the product in three ways: conduction – through direct contact, convection, via currents in the air pocket formed in the insulating jacket, and through radiation. Tracer lines can be constructed of carbon steel, copper or stainless steel. If the product line is constructed of a particular material to accommodate the process fluid, the tracer line material must be selected carefully to avoid electrolytic corrosion at contact points.

Figure 1: Small bore tracing lines can be wrapped around vertical product lines, but this method should not be used on long, horizontal runs. Courtesy: Spirax SarcoFor short tracing runs – around short vertical pipes or valves and fittings – small bore copper pipes (perhaps 0.25 in. bore) may be wound around the product lines (figure 1). The layout should be arranged to provide a continuous fall along the tracers. (Note: Wrap around tracers should be avoided on long horizontal lines.) A run of even 100 ft of 6 in. product line will require 500 to 600 ft of wrap-around tracing. In this scenario, the pressure drop along the tracer would be high and the temperature at the end of the line away from the supply would be low. Indeed, the remote end of the tracer probably would contain only condensate, and the water’s temperature would fall as it continued to give up heat.

Clip-on tracers

The simplest form of external tracer is clipped or wired to the product line. Maximum heat flow is achieved when the tracer is in tight contact with the product line; consequently, the securing clips should not be spaced wider than 12 to 18 in. on 03.75 in. tracers; 18 to 24 in. on 0.5 in. tracers; and 24 to 36 in. on 0.75 in. and larger tracers.

The tracer pipes literally can be wired on, but to maintain close contact, 0.5 in. galvanized or stainless steel bands are better. One practical application method is a packing case banding machine. Where racers are carried around bends, three or more bands should be used to ensure that good contact is maintained. Where it is not possible to use bands as on valve bodies often annealed stainless steel 18 gauge wire is an alternative. With either band material, remember to consider any special needs to avoid external corrosion or electrolytic action.

Welded tracers

Where the temperature difference between the tracer and the product is low, the tracer can be welded to the product line. This can be done either with short-run welds or with a continuous weld for maximum heat transfer. Welded tracer sometimes is laid along the top of the pipe instead of the bottom, greatly simplifying installation. Advocates of this method claim that the location does not adversely affect heat transfer rates.

Figure 2: Heat conducting paste can be placed in the air gap to improve heat transfer. Courtesy: Spirax SarcoHeat conducting paste

For maximum heat transfer, a heat conducting paste can be used to fill the normal hot air gap (figure 2). The paste can be used with any of the clipping methods, but the surface must be wire-brushed clean before applying the past.


If the product being heated is temperature sensitive, it is important to avoid local hot spots on the pipe by introducing a strip of insulation material – fiberglass or mineral wood with packing blocks constructed of inert material to maintain spacing – between the tracer and the product pipe.

Insulation should be used over the tracer line and product pipeline. Three basic methods are used: Aluminum foil (A); preformed, sectional insulation (B); and preformed, sectional molded insulation (C).Insulation should be used over the tracer line and product pipeline. Three basic methods are used: Aluminum foil (A); preformed, sectional insulation (B); and preformed, sectional molded insulation (C).In every installation, insulation should cover both the product line and tracer, but the air space must remain clear. This can be achieved three ways (figure 3)

  • Aluminum foil or galvanized steel sheet can be wrapped around the line and tracing; then, insulation is applied over the sheet or foil. Alternatively, small mesh galvanized wire netting can be used instead of metal sheet.
  • Sectional insulation preformed to one or two sizes larger than the product main can be used. One disadvantage is this insulation can be easily crushed.
  • Preformed sectional insulation designed to cover both product line and tracer can be used. Preformed rigid sectional insulation usually is preferred to plastic material because – rigid insulation retains its thickness and efficiency.

In all cases, the insulation should be finished with waterproof covering: Most insulation is porous, and it is useless as heat-conserving material if it is allowed to absorb water. It also may need to be protected from mechanical damage.

<< First < Previous Page 1 Page 2 Next > Last >>

The Top Plant program honors outstanding manufacturing facilities in North America. View the 2015 Top Plant.
The Product of the Year program recognizes products newly released in the manufacturing industries.
Each year, a panel of Control Engineering and Plant Engineering editors and industry expert judges select the System Integrator of the Year Award winners in three categories.
Doubling down on digital manufacturing; Data driving predictive maintenance; Electric motors and generators; Rewarding operational improvement
2017 Lubrication Guide; Software tools; Microgrids and energy strategies; Use robots effectively
Prescriptive maintenance; Hannover Messe 2017 recap; Reduce welding errors
The cloud, mobility, and remote operations; SCADA and contextual mobility; Custom UPS empowering a secure pipeline
Infrastructure for natural gas expansion; Artificial lift methods; Disruptive technology and fugitive gas emissions
Mobility as the means to offshore innovation; Preventing another Deepwater Horizon; ROVs as subsea robots; SCADA and the radio spectrum
Research team developing Tesla coil designs; Implementing wireless process sensing
Commissioning electrical systems; Designing emergency and standby generator systems; Paralleling switchgear generator systems
Natural gas engines; New applications for fuel cells; Large engines become more efficient; Extending boiler life

Annual Salary Survey

Before the calendar turned, 2016 already had the makings of a pivotal year for manufacturing, and for the world.

There were the big events for the year, including the United States as Partner Country at Hannover Messe in April and the 2016 International Manufacturing Technology Show in Chicago in September. There's also the matter of the U.S. presidential elections in November, which promise to shape policy in manufacturing for years to come.

But the year started with global economic turmoil, as a slowdown in Chinese manufacturing triggered a worldwide stock hiccup that sent values plummeting. The continued plunge in world oil prices has resulted in a slowdown in exploration and, by extension, the manufacture of exploration equipment.

Read more: 2015 Salary Survey

Maintenance and reliability tips and best practices from the maintenance and reliability coaches at Allied Reliability Group.
The One Voice for Manufacturing blog reports on federal public policy issues impacting the manufacturing sector. One Voice is a joint effort by the National Tooling and Machining...
The Society for Maintenance and Reliability Professionals an organization devoted...
Join this ongoing discussion of machine guarding topics, including solutions assessments, regulatory compliance, gap analysis...
IMS Research, recently acquired by IHS Inc., is a leading independent supplier of market research and consultancy to the global electronics industry.
Maintenance is not optional in manufacturing. It’s a profit center, driving productivity and uptime while reducing overall repair costs.
The Lachance on CMMS blog is about current maintenance topics. Blogger Paul Lachance is president and chief technology officer for Smartware Group.
The maintenance journey has been a long, slow trek for most manufacturers and has gone from preventive maintenance to predictive maintenance.
Featured articles highlight technologies that enable the Industrial Internet of Things, IIoT-related products and strategies to get data more easily to the user.
This digital report will explore several aspects of how IIoT will transform manufacturing in the coming years.
Maintenance Manager; California Oils Corp.
Associate, Electrical Engineering; Wood Harbinger
Control Systems Engineer; Robert Bosch Corp.
This course focuses on climate analysis, appropriateness of cooling system selection, and combining cooling systems.
This course will help identify and reveal electrical hazards and identify the solutions to implementing and maintaining a safe work environment.
This course explains how maintaining power and communication systems through emergency power-generation systems is critical.
click me