Ethernet grows but Fieldbus is alive and well!

Ethernet is on the rise and is growing faster than Fieldbus, but overall Fieldbus usage is still greater than Ethernet.

12/09/2011


Another year of information gathering is concluding with the issue of the communications reports. Ethernet, in its various guises continues to increase its share of the market. Just looking around at the publicity and products on view at exhibitions might lead you to believe that it will swamp the market in a few years and fieldbuses will be consigned to the history books. My view is that this will not happen; the evidence for a wholesale switch to Ethernet based technologies is not there. Sure a few companies have seen good growth, I don’t doubt that but node-for-node, Ethernet will gain a few per cent share over the next 5 years.

Figure 1 shows for fieldbuses and Ethernet based protocols, the number of nodes estimated to have been installed in industrial automation networks in 2010 worldwide. At first glance it seems that fieldbuses are expected to forge ahead but in fact their share of the total market is falling.

Figure 1 shows for fieldbuses and Ethernet based protocols, the number of nodes estimated to have been installed in industrial automation networks in 2010 worldwide. At first glance it seems that fieldbuses are expected to forge ahead but in fact their sh

Figure 2 shows the forecast growth rates for 2011 to 2015 and these clearly show that Ethernet growth will slow only a little till 2014 then start to show signs of levelling off. Over the same period the fieldbus growth rate is expected to fall each year, picking up a little in 2015.

Figure 2 shows the forecast growth rates for 2011 to 2015 and these clearly show that Ethernet growth will slow only a little till 2014 then start to show signs of levelling off. Over the same period the fieldbus growth rate is expected to fall each year,

It may come as a surprise to some people that fieldbuses are still growing as fast as they are but there are several reasons why this might be.

  • Ethernet has yet to make an impact at field level; despite high growth rate being reported, the actual numbers are low when compared to nodes connected at control and supervisory level. Ethernet is frequently seen as over complex for use at field level as well as adding extra cost to the device. There are a lot of devices at field level!
  • Fieldbuses are generally much simpler to use.
  • Fieldbuses were in common use 20 years before Ethernet was considered seriously for industrial use, hence there are a lot of legacy systems and the associated knowledge base.
  • New “non-Ethernet” communication technologies and enhancements to existing ones are being added to the list all the time, e.g. I/O Link, AS-Interface, USB, FireWire etc. Some industries have their own favourites: machine vision has CameraLink and CoaXpress; building automation has BACnet and LonWorks.
  • There are many proprietary communication technologies in use today. This is particularly true in Asia, especially Japan, where the adoption of Ethernet in industry has been slow. 

Profile photo of John Morse, a senior analyst for IMS Research. Courtesy: IMS ResearchSo in conclusion; Ethernet grows but fieldbus is alive and well! All the signs are that this will continue for the foreseeable future. Ethernet and its many variants is another story, subject to its own set of rules and trends. Watch this space for the next exciting chapter!



No comments
The Top Plant program honors outstanding manufacturing facilities in North America. View the 2015 Top Plant.
The Product of the Year program recognizes products newly released in the manufacturing industries.
The Engineering Leaders Under 40 program identifies and gives recognition to young engineers who...
IIoT grows up; Six ways to lower IIoT costs; Six mobile safety strategies; 2017 Salary Survey
2016 Top Plant; 2016 Best Practices on manufacturing progress, efficiency, safety
2016 Product of the Year; Diagnose bearing failures; Asset performance management; Testing dust collector performance measures
Future of oil and gas projects; Reservoir models; The importance of SCADA to oil and gas
Big Data and bigger solutions; Tablet technologies; SCADA developments
SCADA at the junction, Managing risk through maintenance, Moving at the speed of data
What controller fits your application; Permanent magnet motors; Chemical manufacturer tames alarm management; Taking steps in a new direction
Tying a microgrid to the smart grid; Paralleling generator systems; Previewing NEC 2017 changes
Package boilers; Natural gas infrared heating; Thermal treasure; Standby generation; Natural gas supports green efforts

Annual Salary Survey

Before the calendar turned, 2016 already had the makings of a pivotal year for manufacturing, and for the world.

There were the big events for the year, including the United States as Partner Country at Hannover Messe in April and the 2016 International Manufacturing Technology Show in Chicago in September. There's also the matter of the U.S. presidential elections in November, which promise to shape policy in manufacturing for years to come.

But the year started with global economic turmoil, as a slowdown in Chinese manufacturing triggered a worldwide stock hiccup that sent values plummeting. The continued plunge in world oil prices has resulted in a slowdown in exploration and, by extension, the manufacture of exploration equipment.

Read more: 2015 Salary Survey

Maintenance and reliability tips and best practices from the maintenance and reliability coaches at Allied Reliability Group.
The One Voice for Manufacturing blog reports on federal public policy issues impacting the manufacturing sector. One Voice is a joint effort by the National Tooling and Machining...
The Society for Maintenance and Reliability Professionals an organization devoted...
Join this ongoing discussion of machine guarding topics, including solutions assessments, regulatory compliance, gap analysis...
IMS Research, recently acquired by IHS Inc., is a leading independent supplier of market research and consultancy to the global electronics industry.
Maintenance is not optional in manufacturing. It’s a profit center, driving productivity and uptime while reducing overall repair costs.
The Lachance on CMMS blog is about current maintenance topics. Blogger Paul Lachance is president and chief technology officer for Smartware Group.
Motion control advances and solutions can help with machine control, automated control on assembly lines, integration of robotics and automation, and machine safety.
This article collection contains several articles on the vital role of plant safety and offers advice on best practices.
This article collection contains several articles on preventing compressed air leaks and centrifugal air compressor basics and best practices for the "fifth utility" in manufacturing plants.
Maintenance Manager; California Oils Corp.
Associate, Electrical Engineering; Wood Harbinger
Control Systems Engineer; Robert Bosch Corp.
click me