Ethernet for sensor networks? Why it makes sense today

Active (or smart) enclosure-less I/O blocks, supporting industrial Ethernet, can be installed close to the sensors to eliminate logistic complexities of running wire back to a central control panel for each sensor and enable two-way communications among the I/O block and programmable logic controllers (PLCs) or remote terminal units (RTUs).


Enclosure-less I/O blocks, installed close to sensors, remove the need for an additional wire from each sensor to control and active (or smart) enclosure-less I/O blocks enable two-way communications among the I/O block and PLCs or RTUs. Shown is a BeldenSensors are like the “scouts” of the manufacturing world; they collect vital information that keeps a manufacturing plant running effectively, efficiently, and with minimum waste, and they report it to the control system, preferably in time to take corrective action when things are trending awry. Today, thanks to Ethernet, sensors can provide their input on the “superhighway” of the plant floor, providing an effective two-way communication stream that can improve efficiency and profitability.

Sensors traditionally fed their information through wires back to a central location where the signals were decoded and acted upon. A plethora of fieldbus networks evolved that expanded the amounts and kinds of data sensors could communicate, such as complex measurements including pressure, level of a substance in a container or closed area, motion detection, and identification of specific patterns. The downside to this, of course, was the job of managing, maintaining, and training for multiple communication protocols.

Now industrial Ethernet is becoming the de facto communications protocol for plant applications. The argument for separate fieldbus protocols was always that Ethernet did not fully meet the needs of the factory floor. However, with the advent of deterministic Ethernet protocols and zero failover redundancy protocols, the need for a separate fieldbus for relaying sensor data has diminished dramatically. It is possible and desirable to deploy an integrated industrial Ethernet infrastructure that extends from the control center to the very edge of the network—the sensors.

Enclosure-less I/O blocks (also called distribution blocks) are the vehicle that supports running Ethernet all the way to the sensor. Enclosure-less I/O blocks can be installed close to the sensors, thus eliminating the logistics complexities of running single wire back to a central control panel for each sensor. Active (or smart) enclosure-less I/O blocks, supporting industrial Ethernet, enable two-way communications among the I/O block and programmable logic controllers (PLCs) or remote terminal units (RTUs).

Mike Miclot is the vice president of marketing, industrial solutions division, at Belden Americas Group. Courtesy: BeldenAn industrial Ethernet infrastructure facilitated by enclosure-less I/O blocks has the potential to provide significant manufacturing efficiencies and cost savings. Not only can it support control and safety functionality, but also data acquisition that can be used for tracking and traceability, asset management, historical records, and other operations and production needs. In addition, running industrial Ethernet all the way out to the sensors allows plants to be operated under one communications protocol, resulting in less hardware (and operational) complexity. By connecting sensors to industrial Ethernet via enclosure-less I/O blocks, the opportunities for reducing deployment and maintenance costs while increasing overall performance and reliability increase dramatically.

- Mike Miclot is the vice president of marketing, industrial solutions division, at Belden Americas Group. Miclot leads strategy formation and go-to-market planning and execution in support of Belden industrial cable products, as well as Hirschmann, Lumberg Automation, and GarrettCom brand solutions. Edited by Mark T. Hoske, content manager, CFE Media, Control Engineering and Plant Engineering,

No comments
The Top Plant program honors outstanding manufacturing facilities in North America. View the 2013 Top Plant.
The Product of the Year program recognizes products newly released in the manufacturing industries.
The Engineering Leaders Under 40 program identifies and gives recognition to young engineers who...
A cool solution: Collaboration, chemistry leads to foundry coat product development; See the 2015 Product of the Year Finalists
Raising the standard: What's new with NFPA 70E; A global view of manufacturing; Maintenance data; Fit bearings properly
Sister act: Building on their father's legacy, a new generation moves Bales Metal Surface Solutions forward; Meet the 2015 Engineering Leaders Under 40
Cyber security cost-efficient for industrial control systems; Extracting full value from operational data; Managing cyber security risks
Drilling for Big Data: Managing the flow of information; Big data drilldown series: Challenge and opportunity; OT to IT: Creating a circle of improvement; Industry loses best workers, again
Pipeline vulnerabilities? Securing hydrocarbon transit; Predictive analytics hit the mainstream; Dirty pipelines decrease flow, production—pig your line; Ensuring pipeline physical and cyber security
Upgrading secondary control systems; Keeping enclosures conditioned; Diagnostics increase equipment uptime; Mechatronics simplifies machine design
Designing positive-energy buildings; Ensuring power quality; Complying with NFPA 110; Minimizing arc flash hazards
Building high availability into industrial computers; Of key metrics and myth busting; The truth about five common VFD myths

Annual Salary Survey

After almost a decade of uncertainty, the confidence of plant floor managers is soaring. Even with a number of challenges and while implementing new technologies, there is a renewed sense of optimism among plant managers about their business and their future.

The respondents to the 2014 Plant Engineering Salary Survey come from throughout the U.S. and serve a variety of industries, but they are uniform in their optimism about manufacturing. This year’s survey found 79% consider manufacturing a secure career. That’s up from 75% in 2013 and significantly higher than the 63% figure when Plant Engineering first started asking that question a decade ago.

Read more: 2014 Salary Survey: Confidence rises amid the challenges

Maintenance and reliability tips and best practices from the maintenance and reliability coaches at Allied Reliability Group.
The One Voice for Manufacturing blog reports on federal public policy issues impacting the manufacturing sector. One Voice is a joint effort by the National Tooling and Machining...
The Society for Maintenance and Reliability Professionals an organization devoted...
Join this ongoing discussion of machine guarding topics, including solutions assessments, regulatory compliance, gap analysis...
IMS Research, recently acquired by IHS Inc., is a leading independent supplier of market research and consultancy to the global electronics industry.
Maintenance is not optional in manufacturing. It’s a profit center, driving productivity and uptime while reducing overall repair costs.
The Lachance on CMMS blog is about current maintenance topics. Blogger Paul Lachance is president and chief technology officer for Smartware Group.