Waterhammer: How much do you know?

As soon as steam leaves the boiler, condensate takes place in the pipe due to heat loss. This situation is even more intense during the initial supply of steam and when the steam is cold.

10/30/2013


Figure 1: Tiny droplets of condensate can build up with increasing length of the pipe and eventually, it becomes a mass of liquid (solid slug) carried along at high speed. Courtesy: Spirax SarcoAs soon as steam leaves the boiler, condensate takes place in the pipe due to heat loss. This situation is even more intense during the initial supply of steam and when the steam is cold.

Figure 1 demonstrates how tiny droplets of condensate can build up with increasing length of the pipe and eventually, it becomes a mass of liquid (solid slug) carried along at high speed.

When the slug encounters any obstacle such as a change in the pipe direction, it will stop immediately. The kinetic energy of the high speed condensate is suddenly converted into pressure energy which has to be absorbed by the pipework. If the speed is very high or there is a lot of weight, the amount of energy output may be strong enough to crack pipes and rupture the fittings. Even if there is not much speed and weight, the noise created in the system by the impact can be a severe nuisance.

Figure 2: Common sources of trouble are sags in the pipework and incorrect use of concentric reducers. Courtesy: Spirax SarcoThe incidence of waterhammer will be encouraged if pockets of condensate are allowed to build up in low points of the steam system. Common sources of trouble are sags in the pipework and incorrect use of concentric reducers as shown in Figure 2. If the eccentric reducer is installed correctly as shown in Figure 3, collection of condensate will not be allowed. Even a strainer fitted as in Figure 4 is a potential cause of waterhammer. It is better to fit strainers on their sides in steam lines and will prevent the formation of condensate which can be picked up by fast moving steam.

To reduce the possibility of waterhammer, steam lines should be arranged with a gradual fall in the direction of flow and drain points installed at regular intervals and at all low points. Check valves should be fitted after any traps which would otherwise allow condensate to run back into the steam line or equipment during shut down.

Figure 3: If the eccentric reducer is installed correctly, collection of condensate will not be allowed. Courtesy: Spirax SarcoWaterhammer can occur in submerged steam heating coils commonly found in tanks and vats. Although the coils do not have the long uninterrupted lengths of steam mains or space heating pipes, incoming steam still can be condensed very quickly. This results in a large weight of water being carried forward by steam which has a fairly high speed due to the heavy condensate rate. If condensate is lifted to the trap, it is important that the coil falls continuously along its length and is fitted with a loop seal and small bore riser.

Difficulties arise when there is insufficient pressure available at the trap inlet if condensate has to be lifted after the steam trap. The equipment will then waterlog and waterhammer may happen when the steam pressure builds up again. This is especially the case with equipment fitted with automatic temperature controls. The best arrangement in such cases is to drain the condensate by gravity to a vented receiver and use a pump to lift to a higher level.

Figure 4: Even a strainer fitted it is a potential cause of waterhammer. Courtesy: Spirax SarcoIt is recommended to fit steam traps which have a strong resistance such as the thermodynamic or bucket types wherever there is a risk of waterhammer.

Content provided by Spirax Sarco, originally published in Steam News Magazine.



STEVE , MO, UNITED STATES, 11/20/13 03:37 PM:

"..This situation is even more intense during the initial supply of steam and when the steam is cold." If the steam were cold, then it wouldn't be steam. I believe they mean when the piping system is cold...
ROBERT , VA, UNITED STATES, 11/25/13 11:26 AM:

By 'cold', I was thinking that Spirax was referring to the steam losing superheat and moving towards saturation.
The Top Plant program honors outstanding manufacturing facilities in North America. View the 2015 Top Plant.
The Product of the Year program recognizes products newly released in the manufacturing industries.
The Engineering Leaders Under 40 program identifies and gives recognition to young engineers who...
2015 Top Plant: Phoenix Contact, Middletown, Pa.; 2015 Best Practices: Automation, Electrical Safety, Electrical Systems, Pneumatics, Material Handling, Mechanical Systems
A cool solution: Collaboration, chemistry leads to foundry coat product development; See the 2015 Product of the Year Finalists
Raising the standard: What's new with NFPA 70E; A global view of manufacturing; Maintenance data; Fit bearings properly
Special report: U.S. natural gas; LNG transport technologies evolve to meet market demand; Understanding new methane regulations; Predictive maintenance for gas pipeline compressors
Cyber security cost-efficient for industrial control systems; Extracting full value from operational data; Managing cyber security risks
Drilling for Big Data: Managing the flow of information; Big data drilldown series: Challenge and opportunity; OT to IT: Creating a circle of improvement; Industry loses best workers, again
Migrating industrial networks; Tracking HMI advances; Making the right automation changes
Understanding transfer switch operation; Coordinating protective devices; Analyzing NEC 2014 changes; Cooling data centers
Upgrading secondary control systems; Keeping enclosures conditioned; Diagnostics increase equipment uptime; Mechatronics simplifies machine design

Annual Salary Survey

After almost a decade of uncertainty, the confidence of plant floor managers is soaring. Even with a number of challenges and while implementing new technologies, there is a renewed sense of optimism among plant managers about their business and their future.

The respondents to the 2014 Plant Engineering Salary Survey come from throughout the U.S. and serve a variety of industries, but they are uniform in their optimism about manufacturing. This year’s survey found 79% consider manufacturing a secure career. That’s up from 75% in 2013 and significantly higher than the 63% figure when Plant Engineering first started asking that question a decade ago.

Read more: 2014 Salary Survey: Confidence rises amid the challenges

Maintenance and reliability tips and best practices from the maintenance and reliability coaches at Allied Reliability Group.
The One Voice for Manufacturing blog reports on federal public policy issues impacting the manufacturing sector. One Voice is a joint effort by the National Tooling and Machining...
The Society for Maintenance and Reliability Professionals an organization devoted...
Join this ongoing discussion of machine guarding topics, including solutions assessments, regulatory compliance, gap analysis...
IMS Research, recently acquired by IHS Inc., is a leading independent supplier of market research and consultancy to the global electronics industry.
Maintenance is not optional in manufacturing. It’s a profit center, driving productivity and uptime while reducing overall repair costs.
The Lachance on CMMS blog is about current maintenance topics. Blogger Paul Lachance is president and chief technology officer for Smartware Group.
This article collection contains several articles on the vital role that compressed air plays in manufacturing plants.