The 'loadcenter' unit substation concept and World War II

In this "Cut the Copper" installment, we learn about how the shortage of copper forced plant electrical engineers and consulting engineers to become more creative in their designs of electrical power systems for large industrial plants.


During World War II and immediately afterward, U.S. manufacturing industries were running at hyper-speed, expanding as fast as possible to keep up with wartime and post-war demand for products of all types.

Throughout the war, supplies of copper were exceedingly tight. Virtually all of the copper that could be produced and obtained by the U.S. went into the war effort. Demand for things like internal wiring for all of the new ships and planes and tanks, cable and bus for the new plants being built to manufacture the war machinery, and munitions and copper shell casings, all combined to consume virtually all of the copper that was available.

The supply of copper became so tight that for several years the U.S. Mint even coined pennies punched out of steel (zinc plated, to prevent rusting) in order to conserve precious copper for uses strategically more important than pennies.

The overall situation forced plant electrical engineers and consulting engineers to become more creative in their designs of electrical power systems for large industrial plants, and the “Loadcenter Unit Substation” concept was born.

Comparison of copper used with 'loadcenter' approach versus outdoor tranformer and 450 V duct bank.The basic concept was that if you could take medium voltage distribution at 5, 15, or 25 kV, and run it long distances deep inside a big factory over very small conductors, then connect it to step-down transformers located “in the center” of the actual heavy loads, then the very large cross-section low voltage secondary feeder cables could be greatly reduced in length.

So, Askarel-filled “loadcenter unit substations” became instantly popular, and were installed right out in the middle of manufacturing floors or on mezzanines directly above them, in thousands of plants all over the country. Where intelligently designed, the concept could often eliminate the need for about 80% of the copper that otherwise would have been required, so this was great innovation with important consequences. The terms “Loadcenter Unit Substation” and just plain “Loadcenter” stuck in the industry for decades.

This trend continued during the huge industrial expansion immediately after the war. And, over the next 30 years, tens of thousands of Askarel-filled loadcenter substation transformers were produced and installed inside industrial buildings.

No comments
The Top Plant program honors outstanding manufacturing facilities in North America. View the 2013 Top Plant.
The Product of the Year program recognizes products newly released in the manufacturing industries.
The Engineering Leaders Under 40 program identifies and gives recognition to young engineers who...
A cool solution: Collaboration, chemistry leads to foundry coat product development; See the 2015 Product of the Year Finalists
Raising the standard: What's new with NFPA 70E; A global view of manufacturing; Maintenance data; Fit bearings properly
Sister act: Building on their father's legacy, a new generation moves Bales Metal Surface Solutions forward; Meet the 2015 Engineering Leaders Under 40
Cyber security cost-efficient for industrial control systems; Extracting full value from operational data; Managing cyber security risks
Drilling for Big Data: Managing the flow of information; Big data drilldown series: Challenge and opportunity; OT to IT: Creating a circle of improvement; Industry loses best workers, again
Pipeline vulnerabilities? Securing hydrocarbon transit; Predictive analytics hit the mainstream; Dirty pipelines decrease flow, production—pig your line; Ensuring pipeline physical and cyber security
Upgrading secondary control systems; Keeping enclosures conditioned; Diagnostics increase equipment uptime; Mechatronics simplifies machine design
Designing positive-energy buildings; Ensuring power quality; Complying with NFPA 110; Minimizing arc flash hazards
Building high availability into industrial computers; Of key metrics and myth busting; The truth about five common VFD myths

Annual Salary Survey

After almost a decade of uncertainty, the confidence of plant floor managers is soaring. Even with a number of challenges and while implementing new technologies, there is a renewed sense of optimism among plant managers about their business and their future.

The respondents to the 2014 Plant Engineering Salary Survey come from throughout the U.S. and serve a variety of industries, but they are uniform in their optimism about manufacturing. This year’s survey found 79% consider manufacturing a secure career. That’s up from 75% in 2013 and significantly higher than the 63% figure when Plant Engineering first started asking that question a decade ago.

Read more: 2014 Salary Survey: Confidence rises amid the challenges

Maintenance and reliability tips and best practices from the maintenance and reliability coaches at Allied Reliability Group.
The One Voice for Manufacturing blog reports on federal public policy issues impacting the manufacturing sector. One Voice is a joint effort by the National Tooling and Machining...
The Society for Maintenance and Reliability Professionals an organization devoted...
Join this ongoing discussion of machine guarding topics, including solutions assessments, regulatory compliance, gap analysis...
IMS Research, recently acquired by IHS Inc., is a leading independent supplier of market research and consultancy to the global electronics industry.
Maintenance is not optional in manufacturing. It’s a profit center, driving productivity and uptime while reducing overall repair costs.
The Lachance on CMMS blog is about current maintenance topics. Blogger Paul Lachance is president and chief technology officer for Smartware Group.