Sports, entertainment venues: Electrical and power systems

Sports arenas and entertainment facilities involve complex engineering solutions. Five consulting engineers share details on electrical and power systems.

04/24/2013


Keith Cooper, PE, President, McClure Engineering, St. Louis. Courtesy: McClure EngineeringDouglas H. Evans, PE, FSFPE, Fire Protection Engineer, Clark County, Nevada. Courtesy: Clark County, NevadaBill Larwood, PE, LEED AP, Senior Vice President/Project Principal, Syska Hennessey Group, Los Angeles. Courtesy: Syska Hennessey GroupKevin Lewis, PE, LEED AP BD+C, Vice President, Henderson Engineers, Lenexa, Kansas. Courtesy: Henderson EngineersBruce McKinlay, Principal, Arup, Los Angeles. Courtesy: Arup

Participants (left to right):

Keith Cooper, PE, President, McClure Engineering, St. Louis

Douglas H. Evans, PE, FSFPE, Fire Protection Engineer, Clark County, Nevada

Bill Larwood, PE, LEED AP, Senior Vice President/Project Principal, Syska Hennessey Group, Los Angeles

Kevin Lewis, PE, LEED AP BD+C, Vice President, Henderson Engineers, Lenexa, Kansas

Bruce McKinlay, Principal, Arup, Los Angeles 


CSE: Describe some recent electrical/power system challenges you encountered when designing a new building or updating an existing building.

Lewis: As part of a press box renovation, we were asked to reuse the existing 1600 A switchboard. At first this was not expected to be a problem. However, as the design progressed, electrical loads such as kitchen equipment, AV equipment, and sports lighting were added to the project that were not originally anticipated. Ultimately, we were able to reuse the existing board, but not without replacing the main circuit breaker to be rated for 100% capacity and also telling the owner that some of the equipment on its “wish list” could not be accommodated without increasing the service size.

The team at Arup helped execute systems at the Singapore Sports Hub, which features a 55,000-seat stadium with a retractable roof that has an LED lighting system, making it the largest programmable LED screen in the world. Courtesy: OakerMcKinlay: With the recent power failure at the Super Bowl, it is very apparent how important resilient and redundant power systems are. The challenges are designing electrical service and switchgear equipment without a single point of failure and also with a robustness that can accommodate varying power demands. This costs money and space, and some utility infrastructure does not offer redundant services so standby power systems are necessary.

CSE: Describe a recent project in which you specified backup, standby, or emergency power in such a facility.

Cooper: Cost seems to be the biggest challenge from project to project. The lists of “what we have to back up,” “what we would like to back up,” and “what we might want to back up some day” usually are at odds with the project budget. This normally leads to bid alternates, which can become confusing due to the effects each alternate has on where equipment is fed from, potential equipment voltage changes, how the one-line diagram changes, and the size of the generator(s). One of the most important parts of the process becomes creation of a final construction set of drawings that accurately reflect the work for the accepted alternates while removing work that will not be part of the to-be-built construction.

Lewis: We were asked to provide a standby generator for backup power as part of a press box remodel project. The existing 100 kW generator was too small to be reused but had to remain in place to provide power to other existing loads. This presented some unique challenges in determining which existing loads would remain in place and how to reroute feeders to allow these loads to remain. Ultimately, we were able to define a good break point in the existing system, which enabled us to remove loads as necessary and minimize cable rerouting and reconnection.

CSE: What is your primary choice for backup, standby, or emergency power?

McKinlay: For sports venues the common source standby or emergency power would be an oil-fired generator. In addition we would recommend two sources from the electrical utility and UPS power with batteries to serve broadcast systems. Use of the grid supply as backup and generator power for the game can ensure minimum switch-over time with UPS systems to achieve FIFA broadcast compliance, for example.

Evans: Because the loads are too large for batteries, generators must be used to provide the secondary power for these facilities. Some of the specific loads (e.g., emergency lighting) can be provided via battery backup.

Lewis: The choice for providing backup power has much to do with the size of the project and the project budget. For large projects, our first choice is to provide a diesel generator sized in accordance with NFPA 110 to power both emergency and legally required standby loads. However, smaller projects often cannot afford this. In these instances, we typically will use emergency batteries to provide backup power to emergency light fixtures.

CSE: What low- and medium-voltage challenges have you encountered in these facilities, such as communications, satellite uplinks, etc.?

Lewis: Low-voltage cabling pathways tend to be a challenge. Many end users like to use cable tray as the primary pathway because of accessibility and ease of maintenance. However, it can be difficult to provide adequate access to cable tray because of coordination with ductwork, piping, light fixtures, conduit, etc. Also, because cable tray must be accessible, it cannot be located above hard ceilings. It can be routed above lay-in ceilings, but this reduces some of the flexibility of cable tray. Additionally, limited structure heights often create significant challenges in locating the tray.



No comments
The Top Plant program honors outstanding manufacturing facilities in North America. View the 2015 Top Plant.
The Product of the Year program recognizes products newly released in the manufacturing industries.
The Engineering Leaders Under 40 program identifies and gives recognition to young engineers who...
2016 Engineering Leaders Under 40; Future vision: Where is manufacturing headed?; Electrical distribution, redefined
Strategic outsourcing delivers efficiency; Sleeve bearing clearance; Causes of water hammer; Improve air quality; Maintenance safety; GAMS preview
World-class maintenance: The three keys to success - Deploy people, process and technology; 2016 Lubrication Guide; Why hydraulic systems get hot
Flexible offshore fire protection; Big Data's impact on operations; Bridging the skills gap; Identifying security risks
The digital oilfield: Utilizing Big Data can yield big savings; Virtualization a real solution; Tracking SIS performance
Getting to the bottom of subsea repairs: Older pipelines need more attention, and operators need a repair strategy; OTC preview; Offshore production difficult - and crucial
Applying network redundancy; Overcoming loop tuning challenges; PID control and networks
Driving motor efficiency; Preventing arc flash in mission critical facilities; Integrating alternative power and existing electrical systems
Package boilers; Natural gas infrared heating; Thermal treasure; Standby generation; Natural gas supports green efforts

Annual Salary Survey

Before the calendar turned, 2016 already had the makings of a pivotal year for manufacturing, and for the world.

There were the big events for the year, including the United States as Partner Country at Hannover Messe in April and the 2016 International Manufacturing Technology Show in Chicago in September. There's also the matter of the U.S. presidential elections in November, which promise to shape policy in manufacturing for years to come.

But the year started with global economic turmoil, as a slowdown in Chinese manufacturing triggered a worldwide stock hiccup that sent values plummeting. The continued plunge in world oil prices has resulted in a slowdown in exploration and, by extension, the manufacture of exploration equipment.

Read more: 2015 Salary Survey

Maintenance and reliability tips and best practices from the maintenance and reliability coaches at Allied Reliability Group.
The One Voice for Manufacturing blog reports on federal public policy issues impacting the manufacturing sector. One Voice is a joint effort by the National Tooling and Machining...
The Society for Maintenance and Reliability Professionals an organization devoted...
Join this ongoing discussion of machine guarding topics, including solutions assessments, regulatory compliance, gap analysis...
IMS Research, recently acquired by IHS Inc., is a leading independent supplier of market research and consultancy to the global electronics industry.
Maintenance is not optional in manufacturing. It’s a profit center, driving productivity and uptime while reducing overall repair costs.
The Lachance on CMMS blog is about current maintenance topics. Blogger Paul Lachance is president and chief technology officer for Smartware Group.
This article collection contains several articles on the vital role that compressed air plays in manufacturing plants.
This article collection contains several articles on the Industrial Internet of Things (IIoT) and how it is transforming manufacturing.
This article collection contains several articles on strategic maintenance and understanding all the parts of your plant.
click me