Sensors, controls improve beer: Less oxygen, better beer

Oxygen in beer reduces shelf life and can affect flavor. Advanced optical measurement and sensor diagnostic technologies minimizes oxygen, simply and dependably.

12/12/2011


Oxygen in the brewing process is monitored because of its importance on the quality, taste and shelf life of the beer. After fermentation, beer is close to being oxygen free and maintaining this very low oxygen level is important for quality assurance. Therefore O2 uptake during the following separation, filtration, storage and filling processes has to be minimized. To reduce the risk of contamination, permanent and precise oxygen monitoring is required.

The InPro6970i has reduced signal drift and faster response time compared to amperometric sensors guarantees maximum accuracy of the oxygen measurement and allow for enhanced process control. Courtesy: Mettler ToledoContinuous measuring of oxygen concentration places high demands on an in-line O2 system. Such equipment must be easy to install and operate, require minimal maintenance and, most importantly, always measure accurately.

Intelligent optical sensor

The InPro 6970i from Mettler-Toledo delivers at low oxygen levels down to 2 ppb. Based on fluorescence quenching technology, it combines high measurement performance with Intelligent Sensor Management (ISM) functionality.

Optical oxygen sensors offer many advantages over amperometric sensors; reduced and easier maintenance, and long term stability resulting in reduced cost of ownership being only two of them. The only consumable, the OptoCap, has a significantly longer lifetime then amperometric membrane bodies and can easily be replaced within a few minutes. No polarization or liquid handling is necessary. Once the sensor is calibrated it is ready to use.

ISM technology adds to these advantages by simplifying maintenance planning and documentation of all sensor data. Using advanced diagnostic tools, the quality of the sensing element and all sensor components are permanently monitored. Early signs of sensor aging or failure are immediately displayed to the user.

With Plug and Measure, the sensor can be connected to an M400 transmitter, and all data, including calibration and information about the sensor history, e.g. the stresses that the sensor has been exposed to, the number of CIP cycles and much more, are transferred to the transmitter. The system becomes ready for use within a few seconds and no complicated configuration or failure prone calibration at the point of use is required.

http://www.mt.com/InPro6970i

http://www.mt.com/InPro6970i 

www.mt.com/ISM 

Mettler Toledo

- Edited by Chris Vavra, Control Engineering, www.controleng.com 

For other Control Engineering fermentation articles, see below.



No comments
The Top Plant program honors outstanding manufacturing facilities in North America. View the 2015 Top Plant.
The Product of the Year program recognizes products newly released in the manufacturing industries.
Each year, a panel of Control Engineering and Plant Engineering editors and industry expert judges select the System Integrator of the Year Award winners in three categories.
2017 Lubrication Guide; Software tools; Microgrids and energy strategies; Use robots effectively
Prescriptive maintenance; Hannover Messe 2017 recap; Reduce welding errors
Safety standards and electrical test instruments; Product of the Year winners; Easy and safe electrical design
Infrastructure for natural gas expansion; Artificial lift methods; Disruptive technology and fugitive gas emissions
Mobility as the means to offshore innovation; Preventing another Deepwater Horizon; ROVs as subsea robots; SCADA and the radio spectrum
Future of oil and gas projects; Reservoir models; The importance of SCADA to oil and gas
Diagnostic functions for system safety; Specifying industrial enclosures; Effective decision support for a crisis
Transformers; Electrical system design; Selecting and sizing transformers; Grounded and ungrounded system design, Paralleling generator systems
Natural gas for tomorrow's fleets; Colleges and universities moving to CHP; Power and steam and frozen foods

Annual Salary Survey

Before the calendar turned, 2016 already had the makings of a pivotal year for manufacturing, and for the world.

There were the big events for the year, including the United States as Partner Country at Hannover Messe in April and the 2016 International Manufacturing Technology Show in Chicago in September. There's also the matter of the U.S. presidential elections in November, which promise to shape policy in manufacturing for years to come.

But the year started with global economic turmoil, as a slowdown in Chinese manufacturing triggered a worldwide stock hiccup that sent values plummeting. The continued plunge in world oil prices has resulted in a slowdown in exploration and, by extension, the manufacture of exploration equipment.

Read more: 2015 Salary Survey

Maintenance and reliability tips and best practices from the maintenance and reliability coaches at Allied Reliability Group.
The One Voice for Manufacturing blog reports on federal public policy issues impacting the manufacturing sector. One Voice is a joint effort by the National Tooling and Machining...
The Society for Maintenance and Reliability Professionals an organization devoted...
Join this ongoing discussion of machine guarding topics, including solutions assessments, regulatory compliance, gap analysis...
IMS Research, recently acquired by IHS Inc., is a leading independent supplier of market research and consultancy to the global electronics industry.
Maintenance is not optional in manufacturing. It’s a profit center, driving productivity and uptime while reducing overall repair costs.
The Lachance on CMMS blog is about current maintenance topics. Blogger Paul Lachance is president and chief technology officer for Smartware Group.
The maintenance journey has been a long, slow trek for most manufacturers and has gone from preventive maintenance to predictive maintenance.
Featured articles highlight technologies that enable the Industrial Internet of Things, IIoT-related products and strategies to get data more easily to the user.
This digital report will explore several aspects of how IIoT will transform manufacturing in the coming years.
Maintenance Manager; California Oils Corp.
Associate, Electrical Engineering; Wood Harbinger
Control Systems Engineer; Robert Bosch Corp.
This course focuses on climate analysis, appropriateness of cooling system selection, and combining cooling systems.
This course will help identify and reveal electrical hazards and identify the solutions to implementing and maintaining a safe work environment.
This course explains how maintaining power and communication systems through emergency power-generation systems is critical.
click me