MEMS differential pressure sensor for liquids and gases

New sensor family from AST handles high pressure limits and wide turndown range.


American Sensor Technologies, Inc. offers the AST5400 wet / wet differential pressure sensor to measure line pressures up to 2,000 PSI with a turndown ratio of 15:1. American Sensor Technologies, Inc. offers the AST5400 wet / wet differential pressure sensor to measure line pressures up to 2,000 PSI with a turndown ratio of 15:1. This cost-effective unit offers many features needed by process industries combined with an economical price. The AST5400 differential pressure sensor can be used to measure differential pressure across a filter, monitor level in a sealed or vented tank, or calculate flow across an orifice plate. 

AST says that using its Krystal Bond technology, these sensors contains no silicone oil, O-rings, or welds, and with its high line pressure capability, this design can be installed into systems without five-way equalization valves, thus saving users hundreds of dollars per installation. This MEMS technology completely isolates the media to the pressure ports, thus eliminating contamination risk. The low strain level on the diaphragm results in accurate, repeatable measurements over a long service life.

The AST5400 replaces systems that use two gauge pressure sensors to calculate differential pressure, saving on installation time and cost. Because the error of two sensor systems is additive, this approach can easily increase performance over temperature.

With advancements in electronics, users of differential pressure switches can now make use of a sensor to monitor system performance and trends in applications requiring a high turn-down and high cycle performance. Alarm functions can be added through most controllers, thus making the need for a separate pressure switch obsolete.

With digital compensation, the AST5400 series provides excellent linearity and performance over a wide temperature range. The electronics offer a failsafe condition on the output signal: if the transducer experiences a fault condition, it can be programmed to move the output signal to 10% below the minimum, or 10% above maximum output signal to notify the user of an issue and protect the system from undesirable conditions.

Visit the Control Engineering Process Control Channel.

Edited by Peter Welander,

No comments
The Top Plant program honors outstanding manufacturing facilities in North America. View the 2013 Top Plant.
The Product of the Year program recognizes products newly released in the manufacturing industries.
The Engineering Leaders Under 40 program identifies and gives recognition to young engineers who...
A cool solution: Collaboration, chemistry leads to foundry coat product development; See the 2015 Product of the Year Finalists
Raising the standard: What's new with NFPA 70E; A global view of manufacturing; Maintenance data; Fit bearings properly
Sister act: Building on their father's legacy, a new generation moves Bales Metal Surface Solutions forward; Meet the 2015 Engineering Leaders Under 40
Cyber security cost-efficient for industrial control systems; Extracting full value from operational data; Managing cyber security risks
Drilling for Big Data: Managing the flow of information; Big data drilldown series: Challenge and opportunity; OT to IT: Creating a circle of improvement; Industry loses best workers, again
Pipeline vulnerabilities? Securing hydrocarbon transit; Predictive analytics hit the mainstream; Dirty pipelines decrease flow, production—pig your line; Ensuring pipeline physical and cyber security
Upgrading secondary control systems; Keeping enclosures conditioned; Diagnostics increase equipment uptime; Mechatronics simplifies machine design
Designing positive-energy buildings; Ensuring power quality; Complying with NFPA 110; Minimizing arc flash hazards
Building high availability into industrial computers; Of key metrics and myth busting; The truth about five common VFD myths

Annual Salary Survey

After almost a decade of uncertainty, the confidence of plant floor managers is soaring. Even with a number of challenges and while implementing new technologies, there is a renewed sense of optimism among plant managers about their business and their future.

The respondents to the 2014 Plant Engineering Salary Survey come from throughout the U.S. and serve a variety of industries, but they are uniform in their optimism about manufacturing. This year’s survey found 79% consider manufacturing a secure career. That’s up from 75% in 2013 and significantly higher than the 63% figure when Plant Engineering first started asking that question a decade ago.

Read more: 2014 Salary Survey: Confidence rises amid the challenges

Maintenance and reliability tips and best practices from the maintenance and reliability coaches at Allied Reliability Group.
The One Voice for Manufacturing blog reports on federal public policy issues impacting the manufacturing sector. One Voice is a joint effort by the National Tooling and Machining...
The Society for Maintenance and Reliability Professionals an organization devoted...
Join this ongoing discussion of machine guarding topics, including solutions assessments, regulatory compliance, gap analysis...
IMS Research, recently acquired by IHS Inc., is a leading independent supplier of market research and consultancy to the global electronics industry.
Maintenance is not optional in manufacturing. It’s a profit center, driving productivity and uptime while reducing overall repair costs.
The Lachance on CMMS blog is about current maintenance topics. Blogger Paul Lachance is president and chief technology officer for Smartware Group.