Machine Safety: Are the stopping categories confusing?

My e-stops are validated to achieve a Category 0 stop function. Therefore, of the three stopping categories, we’re stopping machine motion the quickest way possible. Right? (Standards are cited below. Are they clear enough?)

07/10/2012


My e-stops are validated to achieve a Category 0 stop function. Therefore, of the three stopping Categories, we’re stopping machine motion the quickest way possible. Right?

Machine safety photo courtesy of JB TITUS & ASSOCIATES

(Photo courtesy of JB TITUS & ASSOCIATES)

 

Machine experts often talk about the machine stopping Categories in comparison to the hazard Categories. This is because the hazard Categories are from lowest to highest – B, 1, 2, 3 and 4.

 

In contrast, the machine stopping Categories are from highest to lowest – 0, 1 and 2. This is one of the first areas of confusion around machine safety. The most severe hazard Category is Cat 4 whereas the most significant stopping Category is Cat 0 as described by machine safety standards.

 

However, is there additional confusion when you drill into what the standards actually say about the three stopping Categories?

 

In my experience, yes! First of all let’s look at what one of the most prevalent standards says in describing the stopping Categories:

 

NFPA 79 – 2012, Electrical Standard for Industrial Machinery

Clause 9.2.2 Stop Functions. Stop functions shall operate by de-energizing that relevant circuit and shall override related start functions. The reset of the stop functions shall not initiate any hazardous conditions. The three categories of stop functions shall be as follows:

(1) Category 0 is an uncontrolled stop by immediately removing power to the machine actuators.

(2) Category 1 is a controlled stop with power to the machine actuators available to achieve the stop then remove power when the stop is achieved.

(3) Category 2 is a controlled stop with power left available to the machine actuators.

 

Pretty straight forward, huh? Well, we’ve already said that stopping Cat 0 is determined as the most significant. But, many users say it appears that per definition it’s an uncontrolled stop where all power is removed from all actuators. This means that on certain kinds of machinery (such as direct drive) the machine movement will coast to a stop and rotating energy (such as a fly wheel) will coast to a stop.

 

If “most significant” equals the “shortest time” duration does a Cat 0 stop achieve the shortest time?

 

All safety standards require that an e-stop function shall achieve either a Cat 0 or Cat 1 stop as determined by the risk assessment. So, a Cat 1 stop is a controlled stop with power to machine actuators is maintained to achieve the stop. Then, power is removed from the actuators after the stop of machine motion is achieved. Okay, folks around machines say that this approach is designed to keep power to machine actuators in order to apply full friction braking, reverse current braking, etc. until all machine motion has stopped and then remove all power.

 

 If “most significant” equals the “shortest time” duration does a Cat 1 stop achieve the shortest time?

 

What is your opinion? Are the standards clear enough on these definitions? It appears that a Cat 0 stop which removes all power can not apply any braking to shorten the stopping of all movement. Lacking any further definition by the standards, is a Cat 0 stop the most significant or is a Cat 1 stop the most significant? Which of these two stops causes the most stress on the machine? A Cat 2 stop is not considered in this confusion argument because it’s considered a normal cycle stop. 

 

Your comments or suggestion are always welcome so please let us know your thoughts. Submit

your ideas, experiences, and challenges on this subject in the comments section below. If you don't see a comments box, to controleng.com/blogs, then find this blog under Machine Safety: Machine Safety: Are the stopping Categories confusing?

 

Related reading and articles:

ANSI B11.19-2010, Performance Criteria for Safeguarding

NFPA 79 – 2012, Electrical Standard for Industrial Machinery

E-Stops and Your Compliance

E-Stops Aren’t Safety Devices

 

Contact: www.jbtitus.com for “Solutions for Machine Safety”.



No comments
The Top Plant program honors outstanding manufacturing facilities in North America. View the 2013 Top Plant.
The Product of the Year program recognizes products newly released in the manufacturing industries.
The Leaders Under 40 program features outstanding young people who are making a difference in manufacturing. View the 2013 Leaders here.
The new control room: It's got all the bells and whistles - and alarms, too; Remote maintenance; Specifying VFDs
2014 forecast issue: To serve and to manufacture - Veterans will bring skill and discipline to the plant floor if we can find a way to get them there.
2013 Top Plant: Lincoln Electric Company, Cleveland, Ohio
Case Study Database

Case Study Database

Get more exposure for your case study by uploading it to the Plant Engineering case study database, where end-users can identify relevant solutions and explore what the experts are doing to effectively implement a variety of technology and productivity related projects.

These case studies provide examples of how knowledgeable solution providers have used technology, processes and people to create effective and successful implementations in real-world situations. Case studies can be completed by filling out a simple online form where you can outline the project title, abstract, and full story in 1500 words or less; upload photos, videos and a logo.

Click here to visit the Case Study Database and upload your case study.

Bring focus to PLC programming: 5 things to avoid in putting your system together; Managing the DCS upgrade; PLM upgrade: a step-by-step approach
Balancing the bagging triangle; PID tuning improves process efficiency; Standardizing control room HMIs
Commissioning electrical systems in mission critical facilities; Anticipating the Smart Grid; Mitigating arc flash hazards in medium-voltage switchgear; Comparing generator sizing software

Annual Salary Survey

Participate in the 2013 Salary Survey

In a year when manufacturing continued to lead the economic rebound, it makes sense that plant manager bonuses rebounded. Plant Engineering’s annual Salary Survey shows both wages and bonuses rose in 2012 after a retreat the year before.

Average salary across all job titles for plant floor management rose 3.5% to $95,446, and bonus compensation jumped to $15,162, a 4.2% increase from the 2010 level and double the 2011 total, which showed a sharp drop in bonus.

2012 Salary Survey Analysis

2012 Salary Survey Results

Maintenance and reliability tips and best practices from the maintenance and reliability coaches at Allied Reliability Group.
The One Voice for Manufacturing blog reports on federal public policy issues impacting the manufacturing sector. One Voice is a joint effort by the National Tooling and Machining...
The Society for Maintenance and Reliability Professionals an organization devoted...
Join this ongoing discussion of machine guarding topics, including solutions assessments, regulatory compliance, gap analysis...
IMS Research, recently acquired by IHS Inc., is a leading independent supplier of market research and consultancy to the global electronics industry.
Maintenance is not optional in manufacturing. It’s a profit center, driving productivity and uptime while reducing overall repair costs.
The Lachance on CMMS blog is about current maintenance topics. Blogger Paul Lachance is president and chief technology officer for Smartware Group.