Backlights evolution for human machine interface (HMI) panels

Technology Update: White LEDs show high-temperature advantages for touchscreen HMIs or operator interface backlighting compared to cold cathode fluorescent lamp (CCFL) backlit liquid crystal displays (LCDs).


From cathode ray tube (CRT) displays to cold cathode fluorescent lamp (CCFL) backlit liquid crystal displays (LCDs), and now white light-emitting diode (LED) backlit LCDs, touchscreen HMIs or operator interfaces have come a long way since introduction in the early 1990s. Flat-panel displays have become very popular in the automation industry with applications such as industrial computers and human machine interfaces (HMIs) connecting to PLCs and embedded controller boards.

Figure 1: Comparison of CCFL vs. white LED backlight life measured against temperature. Courtesy: AVG AutomationUnderstanding the history and development of a technology can be a tremendous aid in properly using it for a given application. HMIs, and in particular the backlights behind the HMIs, have evolved significantly for industries such as automotive, medical, packaging, pharmaceuticals, food and beverage, transportation, and many others.

Understanding the technology behind an HMI is very important when deciding which to use. Parameters such as display life, picture quality, and display brightness all come into play when deciding which HMI will best suit an application and its environment. Modern HMIs with LCDs are made up of several components. One of the most significant components of the LCD is its backlight, responsible for the light emanating from the screen. When flat-panel LCDs replaced the older CRT displays like the ones used in older Panelview 1200s and 1400s from Rockwell Automation, there was a significant advancement in each of the above noted parameters. LCDs with a CCFL backlight tremendously enhanced the quality, brightness, and life span of the HMIs as compared to the old CRT displays. CCFL backlight for LCDs began with a life span of only 5,000 hr. The CCFL backlit LCDs improved over time, increasing from 10,000 to 15,000 to 20,000 hr, and all the way up to 50,000 hr of backlight life. Life span for CCFL backlit LCDs depends on the HMI ambient temperature and humidity. CCFL backlit LCDs for more expensive thin-film transistor (TFT) LCDs operating at 25 C (77 F) normally last about 50,000 hr, but the backlight life span dramatically changes with temperature. For example, if the temperature of the LCD rises to about 40 C (104 F), CCFL backlight life deteriorates to roughly 20,000 hr (Figure 1). 

As for relative humidity’s effect on life span, the “wet bulb” temperature of a CCFL backlit HMI is 39 C (102.2 F). Once a CCFL backlit LCD reaches its maximum humidity rating at a given temperature, the backlight will give up (Figure 2).

Figure 2: Relative humidity tolerance of CCFL backlit HMIs. Note: The area under the curve represents safe region, and over the curve is the unsafe region of CCFL backlit HMI operation. Courtesy: AVG Automation

CCFL challenges relate to how they work. The CCFL light source is classified as an electronic component, and is, in simplest terms, a gas-discharge light source, which produces output from a stimulated phosphor coating inside the glass lamp envelope. The typical CCFL is a hollow glass cylinder, coated inside with a phosphor material composed of rare earth elements and sealed with a gettered (impurity-free) electrode at both ends (Figure 3).

Figure 3: CCFL design is shown. Courtesy: AVG Automation

Ultraviolet energy at 253.7 nm is produced by ionization of the mercury and penning gas mixture by the application of high voltage to the electrodes. UV energy from the mercury discharge stimulates the phosphor coating, producing light. A CCFL can be described as a transducer converting electrical energy into light energy. Surprisingly, a CCFL backlit LCD requires a supply voltage of more than 1000 V, typically 1,200-1,500 V. A power-hungry inverter board drives the CCFL backlight (Figure 4).

Figure 4: Example of a conventional CCFL inverter board and CCFL backlight bulb. Courtesy: AVG Automation

Despite the name, cold cathodes don’t remain cold as they operate; they can get painfully hot, which is problematic for CCFL backlit LCDs. The increase in the backlight temperatures significantly reduces life span and can cause erratic operation. HMIs are shipped globally, including India, Mexico, China, and the Middle East, where ambient temperatures reach 45 C (113 F) with 95% humidity.

For longer life and higher reliability, high-end manufacturers are turning to high-efficiency white LEDs, solid-state devices that consist of a chip of semiconducting materials doped with impurities to create a p-n junction. As in other diodes, current flows easily from the p-side (anode) to the n-side (cathode). Figure 5 shows LED construction.

Figure 5: Parts of an LED. Courtesy: AVG Automation

Unlike CCFLs, white LEDs do not have gases and phosphors requiring high voltages but can operate in the range of 5 V to 24 V without an inverter board, generating less heat than CCFLs. White LED backlit LCD displays generally last twice as long as CCFL backlights—75,000 h to 100,000 hr without temperature effects (Figure 1). CCFL backlit LCD displays have 25 C operating temperatures; white have LED-based backlights capable of operating up to 60 C (140 F) in humidity up to 95% (Figure 6).

Figure 6: Relative humidity tolerance of white LED backlit HMIs. Areas under the plot represent a safe region whereas areas over the plot represent unsafe regions of operation for white LED backlit HMIs. (Compare to the smaller safe region for CCFLs in Fi

LED-based lighting has high efficiency as measured by light output per unit power input. Standard touchscreen HMI brightness is often measured in NITS (lumens / sq meter). An HMI with white LED backlights normally exhibits roughly 500 nits, compared to the CCFL backlit LCD displays at roughly 200-300 nits. With a white LED backlit LCD, the backlight life span increases twofold, and brightness increases.

Redundancy is another advantage. When a CCFL bulb fails, the entire LCD display is impossible to read. With the white LED backlit HMI, if one of the many LEDs burns out, the display dims in proportion, but it still can be used for important machine operation. With HMIs in use in many applications and environments, indoors and outdoors, these are key advantages for white LED use in operator interfaces.

White LED backlighting from AVG Automation include 4, 6, 8, 10, and 15-inch EZTouch touchpanel PCs from; 15-in. shown. Courtesy: AVG AutomationWhite LED backlit LCD displays, with a longer life span, more brightness, and higher temperature ratings, have made significant headway in standard LCD TV displays and notebook computers. Sony has used LED backlights in higher-end slim Vaio notebooks since 2005. In 2007, Asus, Dell, and Apple introduced white LED backlights into some notebook models. In October 2008, Apple announced use of LED backlights for its notebooks, and for a new 24-inch Apple cinema display.

As for the touchscreen HMIs, the Uticor division of AVG Automation introduced the first white LED backlit HMI, with 100,000 hr of backlight at 60 C and covering 95% humidity. Displays are available in 4-, 6-, 8-, 10-, and 15-in. sizes. In areas such as the Indian subcontinent, it is normal to have 45 C ambient with 55-60 C inside the control panel.

- Edited by Mark T. Hoske, content manager, CFE Media, Control Engineering, with information from Vikram Aditya Kumar, vice president, AVG/Uticor.

Inception: Retrofit engineering a white LED for backlighting

Inspiration for white LEDs throughout an HMI product line had a hot beginning.

Shalli Kumar, AVG Automation CEO, shows a cold cathode fluorescent lamp (CCFL) removed from a backlit liquid crystal display (LCD), then retrofit with an LED array for a Uticor Tough Panel HMI. CFE Media photo by Mark T. HoskeShalabh Kumar, AVG Automation CEO, said, “I got the idea for [LED backlighting] when landing in Ahmedabad, India, and the pilot said it was 42 C [108 F] at 7:30 p.m. I asked what the temperature was during the day, and it was 48 C [118 F]. In a manufacturing plant, a panel can easily be subjected to 60 C [140 F], which rapidly decreases operating life. Then we talked to manufacturers whose machines use operator interfaces using CCFL displays. A year and a half life for a screen is not unusual.”

“While some screen manufacturers try to make the bulbs easy to replace, no one we talked to actually replaces them in the field. They replace the entire operator interface [OI], which adds considerable expense,” Kumar said.

Operator panels using white LEDs last up to 6 years, compared to 1.5 to 3 years maximum for CCFLs, with a much higher operating temperature range; in rugged environments, especially in high-temperature areas, the higher initial cost is easily made up by avoiding multiple OI replacements during the same operating period, he suggested.

Kumar said, in the March 14 interview, that AVG is the only company in the world that offers white LED backlight as standard, throughout its Uticor Tough Panel line of HMIs.

- Mark T. Hoske is content manager, CFE Media, Control Engineering.

The Top Plant program honors outstanding manufacturing facilities in North America. View the 2015 Top Plant.
The Product of the Year program recognizes products newly released in the manufacturing industries.
Each year, a panel of Control Engineering and Plant Engineering editors and industry expert judges select the System Integrator of the Year Award winners in three categories.
Doubling down on digital manufacturing; Data driving predictive maintenance; Electric motors and generators; Rewarding operational improvement
2017 Lubrication Guide; Software tools; Microgrids and energy strategies; Use robots effectively
Prescriptive maintenance; Hannover Messe 2017 recap; Reduce welding errors
The cloud, mobility, and remote operations; SCADA and contextual mobility; Custom UPS empowering a secure pipeline
Infrastructure for natural gas expansion; Artificial lift methods; Disruptive technology and fugitive gas emissions
Mobility as the means to offshore innovation; Preventing another Deepwater Horizon; ROVs as subsea robots; SCADA and the radio spectrum
Research team developing Tesla coil designs; Implementing wireless process sensing
Commissioning electrical systems; Designing emergency and standby generator systems; Paralleling switchgear generator systems
Natural gas engines; New applications for fuel cells; Large engines become more efficient; Extending boiler life

Annual Salary Survey

Before the calendar turned, 2016 already had the makings of a pivotal year for manufacturing, and for the world.

There were the big events for the year, including the United States as Partner Country at Hannover Messe in April and the 2016 International Manufacturing Technology Show in Chicago in September. There's also the matter of the U.S. presidential elections in November, which promise to shape policy in manufacturing for years to come.

But the year started with global economic turmoil, as a slowdown in Chinese manufacturing triggered a worldwide stock hiccup that sent values plummeting. The continued plunge in world oil prices has resulted in a slowdown in exploration and, by extension, the manufacture of exploration equipment.

Read more: 2015 Salary Survey

Maintenance and reliability tips and best practices from the maintenance and reliability coaches at Allied Reliability Group.
The One Voice for Manufacturing blog reports on federal public policy issues impacting the manufacturing sector. One Voice is a joint effort by the National Tooling and Machining...
The Society for Maintenance and Reliability Professionals an organization devoted...
Join this ongoing discussion of machine guarding topics, including solutions assessments, regulatory compliance, gap analysis...
IMS Research, recently acquired by IHS Inc., is a leading independent supplier of market research and consultancy to the global electronics industry.
Maintenance is not optional in manufacturing. It’s a profit center, driving productivity and uptime while reducing overall repair costs.
The Lachance on CMMS blog is about current maintenance topics. Blogger Paul Lachance is president and chief technology officer for Smartware Group.
The maintenance journey has been a long, slow trek for most manufacturers and has gone from preventive maintenance to predictive maintenance.
Featured articles highlight technologies that enable the Industrial Internet of Things, IIoT-related products and strategies to get data more easily to the user.
This digital report will explore several aspects of how IIoT will transform manufacturing in the coming years.
Maintenance Manager; California Oils Corp.
Associate, Electrical Engineering; Wood Harbinger
Control Systems Engineer; Robert Bosch Corp.
This course focuses on climate analysis, appropriateness of cooling system selection, and combining cooling systems.
This course will help identify and reveal electrical hazards and identify the solutions to implementing and maintaining a safe work environment.
This course explains how maintaining power and communication systems through emergency power-generation systems is critical.
click me